Filter
Top Products
1
English
GROUNDED, CORD-CONNECTED MACHINES INTENDED FOR USE ON A SUPPLY
CIRCUIT HAVING A NOMINAL RATING LESS THAN 150 VOLTS
If the machine is intended for use on a circuit that has an outlet that looks like the one
illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illus-
trated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B,
may be used to connect this plug to a matching two-conductor receptacle as shown in
Fig. B if a properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet can be installed by a qualified electrician. The
green-colored rigid ear, lug, and the like, extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box. Whenever the adapter
is used, it must be held in place with a metal screw.
GROUNDED
OUTLET
BOX
GROUNDING PIN
GROUNDING
MEANS
ADAPTER
GROUNDING PIN
A
B
C D
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian
Electric Code.
DANGER: IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE IN QUESTION IS
PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN
CHECK THE RECEPTACLE.
240 Volt, Single-Phase Operation
The motor supplied with your machine is a dual voltage, 120/240 volt motor. It is shipped
ready-to-run for 120 volt operation. However, it can be converted for 240 volt operation. A
qualified electrician should perform the conversion or take the machine to an authorized
D
EWALT service center. When conversion is complete, the machine must conform to the
National Electric Code and all local codes and ordinances.
The machine is converted by rewiring the motor for 240 volts, installing a
240-volt plug on the power supply cord and replacing the switch (if neces-
sary) with one that is rated for 240-volt operation.
The saw with the 240-volt plug should ONLY be connected to an outlet
having the same configuration as the plug illustrated. No adapter is avail-
able or should be used with the 240-volt plug.
DANGER: IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE
IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED
ELECTRICIAN CHECK THE RECEPTACLE.
Double Insulation
If saw is of double-insulated construction, read the following instructions.
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool’s electrical system.
Tools built with this insulation system are not intended to be grounded. As a result, your tool
is equipped with a two prong plug which permits you to use extension cords without concern
for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when oper-
ating this tool. The insulation system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
EWALT
TOOL, CALL US TOLL FREE AT: 1-800-4-D
EWALT (1-800-433-9258)
General Safety Rules
WARNING: Read all instructions before operating product. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
WARNING: FOLLOW ALL WIRING CODES and recommended electrical connections to
prevent shock or electrocution.
Grounding Instructions
If saw is of grounded construction, read the following instructions.
DANGER: SHOCK HAZARD. THIS MACHINE MUST BE GROUNDED WHILE IN USE.
SERIOUS INJURY COULD RESULT.
ALL GROUNDED, CORD-CONNECTED MACHINES
In the event of a malfunction or breakdown, grounding provides a path of least resis-
tance for electric current to reduce the risk of electric shock. This machine is equipped
with an electric cord having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into a matching outlet that is properly installed and grounded
in accordance with all local codes and ordinances. Do not modify the plug provided - if it
will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper
connection of the equipment-grounding conductor can result in risk of electric shock.
The conductor with insulation having an outer surface that is green with or without yel-
low stripes is the equipment-grounding conductor. If repair or replacement of the electric
cord or plug is necessary, do not connect the equipment-grounding conductor to a live
terminal. Check with a qualified electrician or service personnel if the grounding instruc-
tions are not completely understood, or if in doubt as to whether the machine is properly
grounded. Use only three-wire extension cords that have three-prong grounding type
plugs and matching three-conductor receptacles that accept the machine’s plug, as
shown in Fig. A. Repair or replace damaged or worn cord immediately.