Filter
Top Products
4 TS 55 EQ Circular Saw
General Safety Rules
WARNING: Read and understand all instructions listed below.
Failure to heed instructions may result in personal injury,
electrocution, or fire hazard.
Save These Instructions
Work Area Safety
► Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
► Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust or fumes.
► Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.
Electrical Safety
► Double insulated tools are equipped with a polarized plug
(one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change
the plug in any way. Double insulation eliminates the need for
the three wire grounded power cord.
► Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
► Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
► Do not abuse the cord. Never use the cord to carry the tools or
pull the plug from an outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
Extension Cords
All due care should be practiced while using extension cords with
this tool.
► When operating a power tool outside, use an outdoor extension
cord marked “W-A” or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
► Never use an extension cord that is damaged, such as cuts,
exposed wires, or bent/missing prongs.
► Use only extension cords rated for the purpose.
► Use only extension cords rated for the amperage of this tool
and the length of the cord. Using too small of an extension cord
can cause the router to lose power and damage the tool.
Extension Cord Ratings
Cord Length Size (AWG)
<50 Ft. 14
50-100 Ft. 12
100-150 Ft. 10
>150 Ft. Not recommended
Personal Safety
► Stay alert, watch what you are doing, and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A moment
of inattention while operating power tools may result in serious
personal injury.
► Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long hair can be caught
in moving parts.
► Avoid accidental starting. Be sure the switch is off before
plugging in the power cord. Carrying tools with your finger on
the switch or plugging in tools that have the switch on invites
accidents.
► Remove adjusting keys or wrenches before turning the tool on.
A wrench or a key that is left attached to a rotating part of the
tool may result in personal injury.
► Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in
unexpected situations.
► Use safety equipment. Always wear eye protection. Dust mask,
non-skid safety shoes, hard hat, or hearing protection must be
used for appropriate conditions. (Ordinary glasses are NOT
proper eye protection.)
Tool Use and Care
► Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or
against your body is unstable and may lead to loss of control.
► Do not force the tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for
which it is designed.
► Do not use the tool if the switch does not turn it on or off. Any
tool that cannot be controlled with the switch is dangerous and
must be repaired.
► Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool
accidentally.
► Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
► Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools with sharp cutting edges are less likely
to bind and are easier to control.
► Check for misalignment or binding of moving parts, breakage
of parts, and any other condition that may affect the tool's
operation. If damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained tools.
► Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be suitable
for one tool may become hazardous when used on another tool.