Filter
Top Products
Page 4
RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and
understand this operator's manual and all labels affixed to
the tool. Safety is a combination of common sense, staying
alert, and knowing how your cut-off machine works.
READ ALL INSTRUCTIONS
■ KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the cut-off machine's applications
and limitations as well as the specific potential hazards
related to this tool.
■ GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example; pipes, radiators, ranges,
refrigerator enclosures.
■ KEEP GUARDS IN PLACE and in good working order.
■ REMOVE ADJUSTING KEYS AND WRENCHES. Get
in the habit of checking to see that hex keys and adjusting
wrenches are removed from tool before turning it on.
■ KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools
or pieces of work on the machine while it is in operation.
■ DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools near gasoline or other flammable
liquids, in damp or wet locations, or expose them to rain.
Keep the work area well lit.
■ KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or
extension cord while operating.
■ MAKE WORKSHOP CHILD-PROOF with padlocks and
master switches, or by removing starter keys.
■ DO NOT FORCE THE TOOL. It will do the job better and
safer at the rate for which it was designed.
■ USE THE RIGHT TOOL. Do not force the tool or
attachment to do a job it was not designed for. Don't use
it for a purpose not intended.
■ USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of power
and overheating. A wire gage size (A.W.G.) of at least 14
is recommended for an extension cord 25 feet or less in
length. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
■ INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
■ DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry. They can get
caught and draw you into moving parts. Rubber gloves
and nonslip footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
■ ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses; they are NOT safety glasses.
■ PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
■ PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
■ SECURE WORK. Use clamps or a vise to hold work when
practical. It's safer than using your hand and it frees both
hands to operate tool.
■ DO NOT ABUSE CORD. Never yank cord to disconnect
it from receptacle. Keep cord from heat, oil, and sharp
edges.
■ DO NOT OVERREACH. Keep proper footing and balance
at all times.
■ MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
■ DISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, wheels, bits,
cutters, etc., all tools should be disconnected.
■ AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in.
■ USE RECOMMENDED ACCESSORIES. The use of
improper accessories may cause risk of injury.
■ NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the wheel is unintentionally
contacted.
■ CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged must be
properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
■ NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Do not leave tool until it comes to a
complete stop.
■ USE ONLY CORRECT WHEELS. Do not use wheels
with incorrect size holes. Never use wheel washers or
wheel screws that are defective or incorrect. The
maximum wheel capacity of your cut-off machine is 14 in.
(356 mm).
■ DO NOT REMOVE THE MACHINE'S WHEEL GUARDS.
Never operate the machine with any guard or cover
removed. Make sure all guards are operating properly
before each use.
■ KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from wheel. Do not reach underneath work
or around or under the wheel while the wheel is rotating.
Do not attempt to remove cut material while wheel is
moving.