Filter
Top Products
UNPACKING AND CHECKING CONTENTS
TOOLSNEEDED
Medium Screwdriver
Small Screwdriver
P,ie
, , Wrenche
I,I.:,:I',I.I_i,II'Z_ 3/8 in. 7/16 in.
1/2 in. 9116 in.
Combination Square 3/4 in.
Model 113,298141 Table Saw is shipped complete in one
carton but DOES NOT INCLUDE Table Extension, Steel
Legs, or motor.
Model 113.298031 Table Saw is shipped complete n one
carton but INCLUDES Two Table Extensions, Steel Legs,
and Motor.
Model 113.298151 Table Saw is shipped complete in one
carton but INCLUDES One Table Extension, Steel Legs,
and Motor.
Separate all parts from packing materials and check each
one with the illustration and the list of Loose Parts to make
certain all items are accounted for, before discarding any
packing material.
If any parts are missing, do not attempt to assemble the
table saw, plug in the power cord or turn the switch on
until the missing parOs are obtained and are installed
correctly.
Remove the protective oil that is applied to the table top
and edges of the table. Use any ordinary household type
greaseand spot remover.
CAUTION: Never use gasoline, naptha or similar highly
volatile solvents.
Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean, dry cloth.
WARNING: FOR YOUR OWN SAFETY NEVER
CONNECT PLUG TO POWER SOURCE OUTLET UNTIL
ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU
HAVE READ AND UNDERSTAND THE SAFETY AND
OPERATIONAL INSTRUCTIONS.
K
\
G
COMBINATION SQUARE MUST BE TRUE.
STRAIGHT EDGE OF I_OARD
3/4 '1 THICK. THIS EDGE MUST
DRAW LIGHT LINE ON
BOARD ALONG THIS EDGE. _'_\
BE PERFECTLY STRAIGHT.
SHOULD BE NO GAP OR OVERLAP
HEREWHEN SQUARE IS FLIPPED
OVER IN DOTTED POSITION.
LIST OF LOOSE PARTS
Item PartName Qty.
A BladeGuardandSpreader ..................
B Rip Fence ..............................
C OwnersManual ..........................
D Miter Gauge .............................
E Arbor Nut Wrench* .......................
F Switch w! Key ...........................
G Rip FenceGuideBarwith RipScale(Front) ....
H Handwheel .............................
J V-Be,t 1/2 in. x41 in.* ....................
K Pulley, 2-I/2 in.dia.,with 5/8 in.bore* . ......
L Belt andPulley Guard .....................
M Belt GuardClip ..........................
N Self-ThreadingScrew.10-32x 1/2in. long .....
0 Belt GuardSupport .......................
P Belt GuardSupport Bracket ................
Q Motor Base .............................
R SpreaderRod* . .........................
S BladeGuardSupport with Screw* , ..........
T SpreaderSupport* .......................
U Rip FenceGuideBar(Rear) ................
V RipFenceGuideBarRod ..................
*Pkg,of MiscellaneousSmallPartsNo.62751
Consistingof the Following:
W SetscrewWrench,3/32 in................. 1
W SetscrewWrench,1/8 in.................. 1
W SetscrewWrench,5/32 in................. 1
X Self-ThreadingHut ..................... 2
Y Hex HeadScrew,5/16-18 x 1-3/4 in. long ... 2
Y Hex HeadScrew,5/16-18 x 5/8 in. long .... 3
Y Hex HeadScrew,5/16-18 x 1 in.long ...... 4
Y Hex HeadScrew,1/4-20 x 518in. long ..... 2
Y Hex HeadScrew,5/16-18 x 3/4 in. long ...... 1
*Thesepartsarepackagedin LoosePartsBagNo. 62750
SIL_ X Y
3/4
Z AA AC \/
AB
_LE_NGTH (_
AD AG