Filter
Top Products
-11-
BB4<1;H
Disconnect plug from power source
before performing any assembly,
adjustment or repair to avoid possible injury.
1. The miter saw is equipped with a lock pin used to
lock the miter saw in the lower position. To release,
push the handle down slightly and pull the lock pin
to its full out position and rotate 90°.
NOTE:If the lock pin is stuck and will not pull out when
the handle is pushed down slightly, you may have to
adjust the depth stop bolt (see Depth Adjustment,
page 16) slightly so the handle can be pushed down
and the lock pin can be pulled out.
2. Rotate the lower guard by hand. Loosen front
cover screw to a point that cover plate can be lifted
(Figure 1).
3. Rotate the cover plate counterclockwise so the
blade bolt is exposed (Figure 1).
4. Press and hold the arbor lock (See figure on page
9). Use the multi purpose tool or multi purpose “L”
wrench to remove the blade bolt by turning wrench
clockwise.
5. Remove the blade bolt, outer washer and the
blade. Inner washer does not need to be removed
(Figure 2).
6. To install the 12" blade, fit blade between the chip
deflectors and onto the arbor shaft, and onto 1"
support ring on the inner washer (Figure 3). NOTE:
Make sure the rotation arrow on the blade matches
the clockwise rotation arrow on the lower guard.
To avoid injury, do not use a blade
larger or smaller than 12" diameter
and 1" arbor.
7. Replace the outer washer in it’s proper orientation,
and tighten blade bolt finger tight. Press the arbor
lock and tighten blade bolt securely using multi pur-
pose tool or multi purpose “L” wrench, but do not
overtighten.
8. Rotate cover plate clockwise to original position.
Tighten the front cover plate screw.
)867C4= C74 2>E4A?;0C4 B2A4F
!>>B42>E4A?;0C4B2A4F<0H8=
C4A54A4 F8C7 0=3 70=6D? ;>F4A 1;034 6D0A3
#4E4ADB4B0FF8C7>DC2>E4A?;0C4B42DA4;H8=
?;024!>F4A6D0A3F8;;=>C5D=2C8>=?A>?4A;H
9. Be sure the arbor lock is released so the blade
turns freely.
5C4A 8=BC0;;8=6 0 =4F 1;034
<0:4BDA4C741;0343>4B=>C8=
C4A54A4F8C7C74C01;48=B4AC0CC74J0=3J14E4;
?>B8C8>=BLower the blade into the table slot and
check for any contact with the base or turn table struc-
ture. If blade contacts base or table, seek authorized
service.
10. Place multi purpose tool or multi purpose “L”
wrench in rubber grommet in right rear of tool.
=BC0;;0C8>==3'4<>E0;$5)74;034
!
WARNING
!>F4A
D0A3
$DC4A,0B74A
'40A>E4A
%;0C4(2A4F
>E4A
%;0C4
A>=C
>E4A
%;0C4
(2A4F
;034
>;C
*??4A
D0A3
$DC4A,0B74A
==4A,0B74A
(0F1;034
;034>;C
!45C0=3)7A403
==4A
,0B74A
A1>A
(705C
*??4A
D0A3
86DA4;034'4<>E0;
86DA4;0340A3F0A4
86DA4;034=BC0;;0C8>=
!
WARNING
!
WARNING
!
WARNING
2610009642 10/09 E:2610009642 10/09 E 10/20/09 3:17 PM Page 11