Filter
Top Products
7
Airless Paint Systems
Operating Instructions and Parts Manual
www.chpower.com
Quadraflow
TM
Tip
for painting
(12" from surface)
Fan Width (in.) (mm)
.009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .035
4-6 102-152
6-8 152-203
AL3116 AL3117 AL3119 AL3122 AL3125
8-10 203-254
AL2211 AL2213 AL3126 AL3131
10-12 254-305
AL3118 AL3120 AL2215 AL2217 AL3130 AL3132 AL3135 AL3137
AL3139
12-14 305-356
AL3121 AL3124 AL3127 AL2219 AL2221 AL3136 AL3138
AL3140
14-16 356-406
16
-
18 406
-
457
AL3134
Gun Filter 2 types (part #)
l---------AL086101AJ------l l--------------AL086100AJ---------------l
Lacquer, Varnish
Stain, Sealer
Enamel
Exterior Stain
Vinyl, Acrylic, Latex
Vinyl, Oil Base Alkyd
Latex, Acrylic
Block Filler
Elastomer
Ceiling Hi Build, Mil White
St
ruc
t
ura
l
St
ee
l
Heavy Coatings
Water Flow Rate (gpm)
.12 .18 .24 .31 .38 .47 .57 .67 .77
1.03
1.31
(water @ 2000psi,
138
bar)
(lpm)
.49 .69 .91 1.17 1.47 1.79 2.15 2.54 2.96
3.90
4.98
Paint Flow Rate (gpm)
.10 .15 .21 .27 .33 .40 .49 .58 .66
.88
1.12
(latex paint @ 2000psi, 138
bar/1.36 spec. gr.)
(lpm)
.38 .57 .79 1.02 1.25 1.51 1.85 2.20 2.50
3.33
4.24
(gpm)
.25 .25 .33 .40 .50 .60 .75 .88 1.00
1.25
1.50
(lpm)
1.00 1.00 1.25 1.50 1.90 2.30 2.80 3.30 3.80
4.70
5.70
Orifice Size (inches)
Tip Selection Chart
Consult
y
our paint manufacturer for application recommendation
*pump will support tip worn to next larger size.
.029
.031
Pump Minimum
Output*
Wood Interior
Wood Exterior
Masonry
REMOVE FILTER
Operation
(Cont.)
hand, body fingers or hand in front of
spray tip when cleaning or checking for
a cleared tip. Always point the gun
toward the ground or into an empty
container when checking to see if the
tip is cleared or when using a self-
cleaning tip. Always remove tip before
cleaning.
NOTE: When pausing during a paint
job, keep tip clean by locking the gun
and submerging the tip in a small
bucket of paint thinner. This will help
reduce buildup and drying of paint in
tip, tip guard, and gun.
7. When shutting off the sprayer,
follow this procedure.
a. Whenever you stop spraying,
even for a short break, follow the
Pressure Relief Procedure on page 3.
b. Clean the tip and gun as
recommended by your separate
gun instruction manual.
c. Flush the sprayer at the end of
each work day if the material you
are spraying is waterbased, or if it
could harden in the sprayer
overnight. See "Flushing" page 4.
Use a compatible solvent to flush,
then fill the pump and hoses with
an oil based sovent such as mineral
spirits.
d. For long term shutdown or
storage, refer to page 4.
Be sure to relieve
pressure in the
pump after filling with mineral spirits.
!
WARNING
Table 2 - Tip Selection Chart
AL2710