Filter
Top Products
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN972700AV 11/04
Operating Instructions & Parts Manual Models WG2060 and WG2064
Wire Feed
Arc Welder
BUILT TO LAST
Description
This Campbell Hausfeld wire feed welder
is designed to be used on standard 115V
household current. The welder is
equipped with infinite wire speed
control to accurately select the proper
wire feed rate needed for various
welding conditions. Internal components
are thermostatically protected.
This welding system is designed for use
with the Flux Cored Arc Welding
(FCAW) or the Gas Metal Arc Welding
(GMAW) process. As delivered from the
factory, this welder can weld with .024”
(.6mm) to .030” (.8mm) diameter wire in
MIG and .030” (.8mm) to .035” (.9mm)
diameter wire in flux core. A starter
spool of .035” (.9mm) flux cored wire is
included.
COMPONENTS AND CONTROLS
1. Work Clamp – connects to work
piece.
2. Wire Feed Gun with .035” tip.
3. Power Cord – plug into 115 volt
outlet.
4. Light – illuminates if thermostat has
automatically shut welder off.
5. Infinite Wire Speed Control – turn
clockwise to increase wire speed and
counterclockwise to decrease wire
speed.
6. Off/Heat Selector - Selects welding
power and turns welder on. Four
selections are possible: 1 – 2 – 3 – 4.
7. Polarity Box - For changing to
electrode positive or negative polarity.
8. MIG Gas Hookup
9. Wire Feed Compartment
General Safety
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
!
CAUTION
!
WARNING
!
DANGE
R
See page 7 for supply cable
replacement instructions.
Q
U
A
L
I
T
Y
A
S
S
U
R
A
N
C
E
P
R
O
G
R
A
M
Need
Assistance?
Call Us First!
1-800-746-5641
Unpacking
Welding accessories are packed inside
the wire feed compartment on the
side of the welder. When unpacking,
inspect carefully for any damage that may
have occurred during transit. Make sure
any loose fittings and screws, etc., are
tightened before putting unit into service.
Report any missing or damaged
items by calling 1-800-746-5641.
CIRCUIT REQUIREMENTS
This equipment
requires a dedicated
115 volt circuit. Refer to the following
chart for correct circuit breaker or fuse
rating. Do not run other appliances, lights
or tools on this circuit while operating
this equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure to
comply with this recommendation.
!
CAUTION
For parts, manuals, product & service information
visit www.chpower.com
© 2004 Campbell Hausfeld/Scott Fetzer
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
Heat Circuit Breaker or
Selector Slow Blow Fuse
1-2-3 15 amp
4 20 amp
Figure 1 - Welder Components and Controls
3
1
6
4
8
9
5
2
7
Notes
Notes
Notas
44
Wire Feed Arc Welder
Soudeur à l’Arc Alimenté en Fil
Soldadora Por Arco Con Alimentación de Cable