Filter
Top Products
GENERAL SAFETY iNSTRUCTiONS
Read and understand all the instructions below
before using the power tool. These safety
instructions are not meant to cover every possible
condition that could occur. As with any power tool,
common sense, vigilance and due care must be
used.
I.
2.
3.
4,
READ and become familiar with the entire
Operator's Manual. LEARN the tool's applicationl
limitations and possible hazards.
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning ON.
KEEP WORK AREA CLEAN, Cluttered areas and
benches invite accidents.
5. DO NOT USE iN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp locations or expose
them to rain or snow. Keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors and bystanders
should be kept at a safe distance from work area.
7. MAKE WORKSHOP CHILDPROOF with padlocks;
master switches or by removing starter keys.
8. DO NOT FORCE THE TOOL. It will do the job
better and is safer if used at the rate for which it was
designed.
9. USE THE RIGHT TOOL. Do not force the tool or an
attachment to do a job for which it was not designed.
I 0. USE PROPER EXTENSION CORDS. Make sure
your extension cord is in good condition. When
using an extension cord, be sure to use one heavy
enough to carP;/the current your product will draw.
An undersized cord will result in a drop in line
voltage and in loss of power that will cause the tool
to overheaL The table on page 5 shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
11. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry that may get caught in moving parts. Non-
slip footwear is recommended. Wear protective hair
covering to contain long hair.
12. ALWAYS WEAR EYE PROTECTION. Any power
tool can throw debris into the eyes and could cause
permanent eye damage. ALWAYS wear Safety
Goggles (not glasses) that comply with ANSI Safety
standard Z87.1. Everyday eyeglasses
have only impact-resistant lenses. They ARE NOT
safety glasses. NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could cause serious
injury.
13. WEAR A FACE MASK OR DUST MASK, Sawing
operation produces dust.
14. SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand, and
it frees both hands to operate the tool.
15. DISCONNECT TOOLS FROM POWER SOURCE
before servicing and when changing accessories,
such as blades, bits and cutters.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in the OFF position
before plugging in the tool.
17.
USE RECOMMENDED ACCESSORIES. Consult
this Operator's Manual for recommended
accessories. The use of improper accessories may
cause injury to yourself or others.
18. NEVER STAND ON THE TOOL. Serious injury.
could occur if the tool is tipped or if the cutting tool
is unintentionally contacted.
19. CHECK FOR DAMAGED PARTS. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced.
20. NEVER LEAVE THE TOOL RUNNING
UNATTENDED. TURN THE POWER OFF. Do not
walk away from a running tool until the blade comes
to a complete stop, and then unplug the unit.
21. DO NOT OVERREACH, Keep proper footing and
balance at all times.
22. MAINTAIN TOOLS WITH CARE, Keep tools
sharp and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
23. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction or rotation of the blade or
cutter.
24. WARNING: Dust generated from certain materials
can be hazardous to your health. Always operate
the saw in a well-ventilated area and provide for
proper dust removal.
25.
DO NOT loan your tool to another person without
providing him/her with the Operator's Manual.
Be sure he/she learns the tools applications and
possible hazards,
3