Grizzly G0766 Lathe User Manual


  Open as PDF
of 52
 
-46-
Model G0766 (Mfd. Since 07/15)
Labels
Specifications
MODEL G0766
22" X 42" VARIABLE-SPEED WOOD LATHE
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. Avoid getting entangled in rotating workpiece—tie back long hair, roll up long
sleeves, and DO NOT wear loose clothing, gloves, or jewelry.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand to ensure clearance before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece to remove excess material before mounting.
8. Use the lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, or servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or operate in a wet environment.
13. Prevent unauthorized use by children or untrained users.
WARNING!
Manufactured for Grizzly in China
Power Supply: 220V, 1-Ph, 60 Hz, 4A
Motor: 3 HP, 220V, 3-Phase
Spindle Speeds: 100 – 3200 RPM
Distance Between Centers: 42"
Swing Over Bed: 22"
Spindle Taper: MT#2
Tailstock Taper: MT#2
Weight: 496 Lbs.
Date
Serial #
G0766 Machine Labels A
(11/24/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
PANTONE 151 C or RAL 2005
COLOR CODES
G0766
PANTONE 568C
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 711C or RAL 3020
SPINDLE RPM
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
BELT RPM
A
B
100–1200
330–3200
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Motor
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
SPINDLE RPM
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
SPINDLE RPM
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
SPINDLE RPM
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
SPINDLE RPM
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
VARIABLE
SPINDLE SPEED
RANGES
BELT RPM
A
B
100–1200
330–3200
A
B
NOTE: To maximize spindle
torque, use Belt Position B
when turning at speeds less
than 1200 RPM.
Spindle
Motor
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
G0766 Machine Labels B
(1/8/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 151 C or RAL 2005
PANTONE 109 C
COLOR CODES
PANTONE 3005 C or RAL 5005
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
NOTICE
The lathe will not start after the
Emergency STOP button is used
until the Spindle Direction Switch
is returned to the “0” position.
103104
105
98
99
100
101
106
Specifications
MODEL G0766
22" X 42" VARIABLE-SPEED WOOD LATHE
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. Avoid getting entangled in rotating workpiece—tie back long hair, roll up long
sleeves, and DO NOT wear loose clothing, gloves, or jewelry.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand to ensure clearance before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece to remove excess material before mounting.
8. Use the lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, or servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or operate in a wet environment.
13. Prevent unauthorized use by children or untrained users.
WARNING!
Manufactured for Grizzly in China
Power Supply: 220V, 1-Ph, 60 Hz, 4A
Motor: 3 HP, 220V, 3-Phase
Spindle Speeds: 100 – 3200 RPM
Distance Between Centers: 42"
Swing Over Bed: 22"
Spindle Taper: MT#2
Tailstock Taper: MT#2
Weight: 496 Lbs.
Date
Serial #
G0766 Machine Labels A
(11/24/14)
• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
chemical-resistant material
COLOR CODES
G0766
107
102
REF PART # DESCRIPTION REF PART # DESCRIPTION
98 P0766098 SPINDLE SPEED CHART 103 P0766103 EYE/FACE INJURY HAZARD LABEL
99 P0766099 ELECTRICITY LABEL 104 P0766104 MACHINE ID LABEL
100 P0766100 SPINDLE RPM LABEL 105 P0766105 READ MANUAL LABEL
101 P0766101 SPINDLE DIRECTION SWITCH NOTICE 106 P0766106 BEIGE TOUCH-UP PAINT
102 P0766102 MODEL NUMBER LABEL 107 P0766107 GRIZZLY GREEN TOUCH-UP PAINT
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
 previous next