Filter
Top Products
OOPPEERRAATTIINNGG TTHHEE LLAASSEERR
Do not stare into the laser beam. Never aim the beam at
any person or an object other than the work piece. The use of optical instru-
ments with this laser product will increase the chance of eye damage.
UUSSIINNGG TTHHEE LLAASSEERR LLIIGGHHTT
1. Place the workpiece on the table.
2. Press the laser light ON/OFF switch to the “I” position.
3. To turn the laser light off press the laser light ON/OFF switch to the “O” position.
4. To adjust the laser line turn the laser adjustment knob in a counter-clockwise
direction to loosen it and then move it to the left or right until the laser line is in
line with blade. Turn the laser adjustment knob in a clockwise direction to tighten.
The laser guide does not normally present an optical hazard, although staring at the
beam may cause flash blindness.
The laser shall be used and maintained in accordance with the manufacturer’s
instructions.
Always ensure the laser beam is aimed at a sturdy work piece without a reflective
surface, i.e. wood or rough coated surfaces are acceptable. Bright shiny reflective
sheet or the like is not suitable for laser use as the defective surface could direct the
beam back at the operator.
IItt mmaayy bbee mmoorree ddiiffffiiccuulltt ttoo sseeee tthhee llaasseerr lliin
nee iinn ccoonnddiittiioonnss
ooff bbrriigghhtt ssuunnsshhiinnee aanndd oonn cceerrttaaiinn ssuurrffaacceess..
OOPPEERRAATTIINNGG TTHHEE BBAANNDD SSAAWW
Before operating the band saw, the unit should be fully assembled and prepared for
use. All doors should be closed and locked and appropriate safety procedures fol-
lowed.
1. With power removed from the equipment, perform a pre-operation check:
Check for damaged parts. Check that guards are in place. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
2. Correct all unsafe conditions. Any part that is damaged should be properly
repaired or replaced.
LLAASSEERR SSAAFFEETTYY
NNEEVVEERR LLOOOOKK IINNTTOO TTHHEE LLAASSEERR BBEEAAMM..
Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
DDOO NNOOTT AAIIMM TTHHEE LLAASSEERR BBEEAAMM AATT AANNYYOONNEE OORR AATT RREEFFLLEECCTTIIVVEE
SSUURRFFAACCEESS..
CCLLAASSSS 22MM LLAASSEERR PPRROODDUUCCTT..
Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
SSTTOORREE OOUUTT OOFF RREEAACCHH OOFF CCHHIILLDDRREENN..
Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
DDOO NNOOTT TTAAMMPPEERR WWIITTHH TTHHEE LLAASSEERR O
OUUTTPPUUTT..
Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
OOPPEERRAATTIIOONN AACCCCEESSSSIIBBLLEE FFIIEELLDDSS::
Wavelength 636-660nm
Laser Power for Classification <1mW CW
NNEEVVEERR OOPPEERRAATTEE LLAASSEERR IIFF TTHHEE UUNNIITT IISS DDEEFFEECCTTIIVVEE OORR TTHHEE CCOOVVEERR OOR
R SSEEAALL
IISS DDAAMMAAGGEEDD..
DDOO NNOOTT SSEERRVVIICCEE LLAASSEERR..
The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
23 24
LASER LIGHT
DO NOT VI
EW DIRECTLY WITH OPTICAL
INSTRUMENTS (MAGNIFIERS)
CLASS 2M LASER PRODUCT
635-660nm, <1mW CW
CLASSIFIEDS PER IEC 60825-1, Ed. 1.2, 2001-08
A
VOID EXPOSUR
E - LASER
LIGHT IS
E
MI
TTED
FROM THIS A
P
ER
TURE.”
LASER RADIATION
CAUTION LABEL