Filter
Top Products
33
Repair Parts
Parts List For RIDGID Oscillating Edge Belt/Spindle Sander
Model EB44241
RIDGID parts are available on-line at www.ridgidparts.com
Figure 1
Always order by Part Number—Not by Key Number
* Standard Hardware Item - May be purchased locally
† These parts are available where you purchased your sander.
• Any attempt to repair this motor may create a hazard unless repair is done by a qual-
ified service technician. Repair service is available at your nearest Authorized Ser-
vice Center.
Key
No.
Part No. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
826358-1
805553-2
822304
See pg. 29
825808
See pg. 29
810993-2
825841
830291
805297-9
825523
825548
825844
825842
830246
825537
825852
159572-138
808380-7
825840
830456
159572-186
824604
830290
805549-22
Knob, Spindle
Washer
21/64 x 5/8 x 1/32
Drum, Sanding 3/4"
†Drum, Sandpaper
Plate, Throat 2"
†Belt, Sanding 4" x 24"
Screw, Set Half Dog
10/32 x 1/2
Adapter, Throat Plate
Fan
Screw, Flat Hd
1/4-20 x 5/8
Table, Rear
Plate, Wear
Nut, Special Twin 1/4-20
Screw, Shoulder 1/4-20
Chute, Sawdust
Bracket, Table Lock
Knob, 1/4-20 x 3/4
Screw, Wash/Hd
Ty “T” 10-32 x 3/8
Screw, Pan Hd 10-14 x 1/2
Spring, Detent
Base
Screw, Hex Hd
Ty “T” 1/4-20 x 1
Screw, Hex Wash/Hd
Ty “T” 8-32 x 3/8
• Motor/Drive Asm
Washer
13/64 x 3/8 x .031
Key
No.
Part No.
Description
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
826801
825854
819012
9416630
829785
AC1000
817399-11
37837
825549
825537-1
825543
825524
803309-2
825525
825539-1
SP6496
37836
—
805553-30
805553-24
822304-1
822304-2
822304-3
825808-1
825808-2
825808-3
Enclosure
Cord w/Plug
Foot
Screw, Hex Hd Ty “T”
5/16-18 x 1
Switch, Locking
†Key, Switch
Relay
Wrench, Hex “L” 5/32
Spacer, Table Lock
Bracket, Table Lock Left
Bolt, Table Lock
Table, Front
Screw, Soc Set Lock
10-32 x 3/8
Plate, Stop
Knob 1/4-20
Owners Manual
Wrench, Hex “L” 3/32
Belt Sanding Assembly
(See Fig. 2)
* Washer 5/8 x 1-3/4 x 1/8
Washer
21/64 x 7/8 x 3/64
Drum, Sanding 1"
Drum, Sanding 1-1/2"
Drum, Sanding 2"
Plate, Throat 1-1/2"
Plate, Throat 1"
Plate, Throat 1/2"