Filter
Top Products
English
3
9. This system is capable of producing 2800 PSI / 193 Bar
(9145) or 3000 PSI / 207 Bar (9155/9175/9195). Only
use replacement parts or accessories that are specied
by the manufacturer and that are rated a minimum of
3000 PSI. This includes spray tips, nozzle guards,
guns, extensions, ttings, and hose.
10. Always engage the trigger lock when not spraying.
Verify the trigger lock is functioning properly.
11. Verify that all connections are secure before operating
the unit.
12. Know how to stop the unit and bleed pressure quickly.
Be thoroughly familiar with the controls. Pressure will
not be released by turning off the motor. The PRIME/
SPRAY valve or pressure bleed valve must be turned to
their appropriate positions to relieve system pressure.
Refer to PRESSURE RELIEF PROCEDURE described
in the pump manual.
13. Always remove the spray tip before ushing or cleaning
the system.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is
important to treat the injury as soon as possible. DO
concern with some coatings injected directly into the
blood stream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
d) WARNING - To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection,
clothing and a respirator or mask when painting.
Hazardous vapors – Paints, solvents, insecticides, and
other materials can be harmful if inhaled or come in
contact with body. Vapors can cause severe nausea,
fainting or poisoning.
2. Do not operate or spray near children. Keep children
away from equipment at all times.
3. Do not overreach or stand on an unstable support.
Keep effective footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the
inuence of drugs or alcohol.
6. Do not kink or over-bend the hose. Airless hose can
develop leaks from wear, kinking and abuse. A leak
can inject material into the skin.
7. Do not expose the hose to temperatures or pressures in
excess of those specied by manufacturer.
8. Do not use the hose as a strength member to pull or lift
the equipment.
9. Use lowest possible pressure to ush equipment.
10. Follow all appropriate local, state and national codes
governing ventilation, re prevention and operation.
11. The United States Government Safety Standards
have been adopted under the Occupational
Safety and Health Act (OSHA). These standards,
particularly part 1910 of the General Standards and
part 1926 of the Construction Standards should be
consulted.
12. Before each use, check all hoses for cuts, leaks,
abrasion or bulging of cover. Check for damage or
movement of couplings. Immediately replace hose
if any of those conditions exist. Never repair a paint
hose. Replace with a conductive high-pressure
hose.
13. Do not spray outdoors on windy days.
14. Always unplug cord from outlet before working on
equipment (electric models only).
Important Electrical Information
IMPORTANT:
has a 3-blade grounding plug and a 3-slot receptacle
that will accept the plug on the product. Make sure
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. A 14
or 12 gauge cord is recommended (see chart). If
would indicate that the cord would be appropriate
for outdoor use.
Cord gauge Maximum cord length
12 150 feet
14 100 feet
Do not use more than 100 feet of spray hose. If you
need to spray further than 100 feet from your power
hose.
any time during assembly, operation, or cleanup,
please refer to the Troubleshooting section of this
manual (page 22), or call customer service at:
1-800-880-0993
Specifications:
Capacity:
9145...........Up to .29 gallon (1.10 liter) / min
9155...........Up to .33 gallon (1.25 liter) / min
9175...........Up to .38 gallon (1.40 liter) / min
9195...........Up to .42 gallon (1.60 liter) / min
Power source:
9145...........1/2 Hp universal motor
9155...........5/8 Hp universal motor
9175...........3/4 Hp permanent magnet DC motor
9195 ..........7/8 Hp permanent magnet DC motor
Power requirement: 15 amp minimum circuit on 115
VAC, 60 Hz current
Generator power requirement: 5000 Watt