Filter
Top Products
Spindle
pulley
Motor
pulley
Depth scale stop nuts Depth scale
pointer
Cord clamp
Belt
tension
knob
Feed spring
Column collar
Bevel scale
Table suppo_
Depth scale
indle
Feed stop rod
Depth stop
Cove r
ON/OFF
switch w/key
\
Eeed handle
Chuck
Support .eck handle Base
Bevel lock
Table
Fence end__
Fence backstop
Head lock
screw
_b
tor
_._ii i _ Belt
_ tenl_/°nb
Head lock
screw
Column support
,: !. ::::, :
L!
!
BASE - Supports the drill press. For additional stability,
holes are provided in the base to bolt the drill press to
the floor. (See "Specific Safety Instructions for Drill Presses':)
BACKUP MATERIAL -A piece of scrap wood placed
between the workpiece arid table. The :backup board
prevents wood in the workpiece from splintering when the
drill passes through the backside of the workpiece. It also
prevents drilling into the table top.
BELT GUARD ASSEMBLY -Covers the pulleys and belt
during operation of the drill press.
BELT TENSION - Refer to the "Assembly" Section,
"Installing and Tensioning Belt."
_LT TENS!ION KNOB -Tightening the knob locks
the motor bracke t support maintaining correct belt distance
and tension.
BEVEL SCALE - Shows the degree of table tilt for bevel
operations. The scale is mounted on the side of the arm.
CHUCK - Holds the drill bit or other recommended
accessory to perform desired operations.
CHUCK KEY - A self-ejecting chuck key which will pop
out of the chuck when you let go of it. This action is
designed to help prevent throwing of the chuck key from
the chuck when the power is turned "ON". Do not use
any other key as a substitute; order a new one if damaged
or lost.
COLUMN -Connects the head, table, and base on a
one-piece tube for easy alignment and movement.
COLUMN COLLAR - Holds the rack to the column.
Rack remains movable in the collar to permit table
support movements.
COLU_N SUPPORT -Supports the column, guides the
rack and provides mounting holes for cotumn to base.
DEPTH SCALE - lndic_,tes ,depth of hole being drilled
DEPTH SCALE POINTF=R -oindicates the drilling depth
by pointing to the depth scale,
DEPTH SCALLE STOP NUTS - Locks the depth scale to
selected depth.
DRILL BiT - The cutting too! used in the drill press to
make holes in a workpiece.
:; :_::::_::::::_i<!:ii: : ::::::::iii?_i::::::i:',: : : : :
DRILL ON/OFF SWITCH - Has locking feature. This
feature is intended to help prevent unauthorized and
possible hazardous use by children and others, insert the
key into the switch to turn the drill press on.
DRILLING SPEED - Changed by placing the belt in any
of the steps (grooves) in the pulleys. See the Spir_
Speed Chart inside the belt guard.
FEED HANDLE- Moves the chuck up or down. If
necessary, one or two of the handles may be removed
whenever the workpiece is of such unusual shape that it
interferes with the handtes.
FENCE - Attaches to the table to a i:gn the workpiece or
for fast repetitive drilling. Removable. Remove fence when
it interferes with other drill press accessories.
HEAD LOCKS - Locks the head to the column. ALWAYS
lock the head in place while operating the drill press.
RACK -- Combines with gear mechanism to provide easy
elevation of the table by the hand operated table-crank.
REVOLUTION PER MINUTE (R,P,M.)-The number of
turns completed by a spinning object in one minute.
SPINDLE SPEED - The R.RM. of the spindle.
SPRING CAP - Adjusts quill spring tension(
TABLE - Provides working surface to support workpiece.
TABLE BEVEL LOCK - Locks the table in any position
from 0°- 45°.
TABLE CRANK HANDLE - Elevates and lowers table.
Turn clockwise to elevate table. Support lock must be
released before operating crank.
TAB&E SUPPORT LOCK = Tightening locks the table
support to the column. Always have it locked in place
while operating the dril! press,
TABLE SUPP©RT = Rides on the column to s{jppol:t the
table.
WORKP_ECE = Materia! being drilled. '
9 ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::