Filter
Top Products
English
3
Electrical Connection
Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that
your saw will operate on alternating current only. A voltage decrease of 10 percent or more
will cause a loss of power and overheating. All D
EWALT tools are factory tested. If this tool
does not operate, check the power supply.
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts.
In addition to this instruction manual, the carton should contain:
1. One No. DW713 miter saw with blade.
2. One blade wrench in wrench pocket shown in Figure 2.
3. One No. DW7053 Dust Bag.
Familiarization
Your miter saw is fully assembled in the carton.
FIG. 1
Open the box and lift the saw out by the conve-
nient carrying handle, as shown in Figure 1.
Place the saw on a smooth, flat surface such as
a workbench or strong table.
Examine Figures 2 and 3 to become familiar
with the saw and its various parts. The section
on adjustments will refer to these terms and you
must know what and where the parts are.
Press down lightly on the operating handle and
pull out the lock down pin, as shown in Figure 4.
Gently release the downward pressure and allow the arm to rise to its full height. Use the
lock down pin when carrying the saw from one place to another. Always use the carrying
handle to transport the saw or the hand indentations shown in Figure 3.
Specifications
CAPACITY OF CUT
50 degree miter left and right
48 degree bevel left: 3 degree right
0 degree miter
Max. Height 3.5" Result Width 3.5"
Max. Width 6.1" Result Height 1.25"
45 degree miter
Max. Height 3.5" Result Width 2.4"
Max. Width 4.2" Result Height 1.25"
45 degree bevel
Max. Height 2.3" Result Width 3.5"
Max. Width 6.1" Result Height .75"
31.62 degree miter and 33.85 bevel
Max. Width 5.25" Result Height .9"
DRIVE
1600 Watts 15 Amp Motor
5000 RPM Cut Helical Gears with Roller and Ball Bearings
Carbide Tooth Blade Automatic Electric Brake
• NEVER cross arms in front of blade while using tool. Always make a dry run
(unpowered) before making a finish cut so that you can check the path of the blade or
severe personal injury may result.
WARNING: Do not connect unit to electrical power source until complete instructions
are read and understood.
WARNING: Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON
THE TABLE AND AGAINST THE FENCE.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
ON MOTOR HOUSING:
WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE
OPERATING SAW.
WHEN SERVICING, USE ONLY IDENTICAL RE PLACE MENT PARTS.
ALWAYS WEAR EYE PROTECTION.
DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.
ON MOVING FENCE:
ALWAYS ADJUST FENCE PROPERLY
BEFORE USE. Clamp small pieces
before cutting. See manual.ON
GUARD:
DANGER – KEEP AWAY FROM
BLADE.
ON UPPER GUARD:
PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE
USE.
ON TABLE: (2 PLACES)
WARNING: FOR YOUR OWN SAFETY READ INSTRUCTION
MANUAL BEFORE OPERATING MITER SAW.
KEEP HANDS OUT OF PATH OF SAW BLADE.
DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.
CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE.
ALWAYS TIGHTEN ADJUSTMENT BEFORE USE. DO NOT PERFORM ANY
OPERATION FREEHAND.
NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS IN FRONT
OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP BEFORE
MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS.
DISCONNECT POWER BEFORE CHANGING BLADE OR SERVICING.
TO REDUCE THE RISK OF INJURY, ALLOW SAW TO RETURN TO THE
FULL UP POSITION AFTER EACH OPERATION. THINK! YOU CAN PREVENT
ACCIDENTS.