Grizzly G0602 Lathe User Manual


  Open as PDF
of 64
 
BdYZa<%+%'B[\#H^cXZ.$%-
"(("
JhZi]ZhZhiZehidaZVgc]dlidhZijendjgaVi]Z
[dg edlZg[ZY deZgVi^dc#I]Z ZmVbeaZ^c Figure
34 h]dlh aVi]Z hZije [dg V edlZg [ZZY gViZ d[
%#%&'#  GZbZbWZg! Vaa i]Z XVgg^V\Z Y^gZXi^dc ^h
gZkZghZYl]Zche^cYaZgdiVi^dc^hgZkZghZY#
Setting Power Feed
Rate
4. DeZc i]Z h^YZ XdkZg VcY jhZ V +bb ]Zm
lgZcX] id addhZc i]Z aVh] VY_jhiZg Figure
34VcYhl^c\i]ZX]Vc\Z\ZVgVhhZbWandji
d[i]ZlVn#
5. GZbdkZ i]Zhe^cYaZ :"Xa^eh VcYXVe hXgZl!
ajWg^XViZ!VcYhlVedjii]ZX]Vc\Z\ZVgh^c
i]ZdgYZgh]dlcdci]ZX]Vgi^cFigure 34.
Note:All change gears are stamped with the
number of teeth they have.
6. BdkZ i]Z aVh] VY_jhiZg hd i]Z \ZVg WVX`"
aVh]^hWZilZZc%#%%(id%#%%-!i^\]iZci]Z
aVh] VY_jhiZgXVe hXgZl!VcY XadhZi]Z h^YZ
XdkZg#
7. Jh^c\ V *bb ]Zm lgZcX]! addhZc i]Z XVg"
g^V\ZadX` Figure 33! VcYjhZ i]Z]Va[ cji
aZkZg id Zc\V\Z VcY Y^hZc\V\Z i]Z edlZg
[ZZYl]ZcgZfj^gZY#
Figure 33.8Vgg^V\ZadX`VcY[ZZYXdcigda#
8Vgg^V\ZAdX`
8VeHXgZl
=Va[Cji
AZkZg
Figure 34.EdlZg[ZZYhZije#
40
60
27
56
127
104
8]Vc\Z<ZVgh
;ZZY9^Vah
AVh]6Y_jhiZg
= 0.012" Feed
;ZZY8]Vgi
To set and engage the power feed:
1. 9>H8DCC:8IA6I=:;GDBEDL:G
2. Ijgci]Z[ZZYY^Vahidi]ZcjbZgVaVcYaZiiZg
^cY^XViZYWni]ZX]Vgi^c Figure 34#
Note:You may have to rock the chuck by
hand slightly to get the gearbox gears to
engage one another.
3. Jh^c\ i]Z X]Vgi ^c Figure 34! \Vi]Zg i]Z
gZfj^gZYX]Vc\Z\ZVgh#
Feed rate is based on spindle RPM. Pay
close attention to the feed rate you have
chosen and be ready to disengage the
carriage. Failure to do this may cause the
carriage to crash into the chuck.
 previous next