Filter
Top Products
– 16 –
#()!!)$#
(054BG%@420CB8=<A
!$)$#
The machine should be located in a clean, dry place
where there is free circulation of clean air such that air
movement in through the front and out through the
back will not be restricted. Dirt and dust that can be
drawn into the machine should be kept to a minimum.
Failure to observe these precautions can result in
excessive operating temperatures and nuisance shut-
down of the machine.
%%!)$#R!"))$#(
There are no provisions on the CV 500-I for parallel-
ing, and outdoor operations without rain sheltering is
not recommended.
() #
The units may be stacked three high by observing the
following safety precautions.
1. Make sure the first or bottom unit is setting on a
level, well supported surface.
2. The units must be stacked with their fronts flush,
making sure the two holes in the base rails of the
unit being stacked on top are over the two holes
located on the top front corners of the unit it is
being stacked on. Fasten the units together with
5/16 bolts, nuts and lockwashers through these
holes.
3. Remove fastening bolts before lifting unit off stacks.
<>CB%=E4@=<<42B8=<A
By removing the rear access panel the three phase
input power is connected to the three line terminals on
the input contactor, and the earth grounding lead to
the grounding terminal on the input box floor marked
with the symbol. Install the reconnect panel
jumper
links for the proper input voltage per the diagram
pasted
inside the access panel cover.
See Installation Data below:
!)'($ 20<98::
M=<=BB=C274:42B@820::G:8D4>0@BA=@
4:42B@=34E8B7A98<=@E4B2:=B78<6
M<AC:0B4G=C@A4:55@=;E=@90<3
6@=C<3
M:E0GAE40@3@G8<AC:0B8<66:=D4A
*"(#((20<1430<64@
=CA
M 44>G=C@7403=CB=55C;4A
M*A4D4<B8:0B8=<=@4F70CABB=@4;=D4
5C;4A5@=;1@40B78<6H=<4
,!#R(%' (R20<20CA458@4=@
4F>:=A8=<
M 44>5:0;;01:4;0B4@80:0E0G
M=<=BE4:3=<2:=A432=<B08<4@A
'R'.(20<1C@<4G4A0<3A98<
M,40@4G440@0<31=3G
>@=B42B8=<
(44 0338B8=<0: E0@<8<6 8<5=@;0B8=< 0B
5@=<B=5B78A=>4@0B=@SA;0<C0:
,'##
!!#R&*%"#)can cause
injury.
• Do not lift this machine using lift bale if
it is equipped with a heavy accessory
such as trailer or gas cylinder.
• Lift only with equipment of adequate lifting capacity.
• Be sure machine is stable when lifting.
• Do not stack more than three high.
• Do not stack the CV 500-I on top of any other
machine.
---------------------------------------------------------------------
,'##
#()!!)$#R)
<>CB'0B8<6 '42=;;4<3438<>CBE8@40<35CA4A8H4A5=@;0F8;C;@0B43=CB>CB
<0338B8=<5=::=E:0B4AB#0B8=<0::42B@820:=340<3!=20:=34
<>CB,8@4(8H4"8<8;C;@=C<38<6
*(("##(*%'!
;>4@4A** )G>4L=>>4@ ,8@4(8H4
*((/#
=< =<3C2B=@A8< =>>4@=<3C2B=@A
)!$#*"'
+=:B064 4@BH #0;4>:0B4 =<3C8BR, ,*((/)!$
#*"'
220 78 3 (27mm
2
) 8 (10mm
2
) 100 REN-100
230 75 4 (21mm
2
) 8 (10mm
2
) 100 REN-100
380 50/60 45 6 (13mm
2
) 10 (5.3mm
2
) 60 RES-60
400 43 8 (8.4mm
2
) 10 (5.3mm
2
) 60 RES-60
440 39 8 (8.4mm
2
) 10 (5.3mm
2
) 50 RES-50
Ambient temperature of 40°C (104°F).
At rated output of 400A, 100% duty cycle.
*A4=<:GCAA;0<<(C>4@!065CA4AA>4285843$B74@5CA4A;0G<=B>@=B42BB74E4:34@0<3;0G20CA4=D4@
740B8<60<3>=AA81:458@430;064