Filter
Top Products
– 31 –
Only qualified persons should install, use or
service this machine.
using the disconnect switch at the fuse box
WARNING
Turn off input power to the Welding Power Source
Before connecting the wire feeder.
ELECTRIC
SHOCK
CAN KILL
S21038
CV-
+
N.C.
ELECTRODE CABLE
TO LN-7
14 PIN
AMPHENOL
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.C.
76
82
81
SPARE
2
4
41
42
31
32
GND
21
77
75
REMOTE OUTPUT CONTROL
CONNECT TOGETHER FOR
WELDING OUTPUT
115 VAC / 2 AMP
}
}
}
N.D.
2
4
10K
MIN.
NOT USED
FRAME CONNECTION
}
NOT USED
NOT USED
}
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT
AND DUTY CYCLE OF APPLICATION.
N.B. DIAGRAM SHOWS ELECTRODE POSITIVE. TO CHANGE
POLARITY, TURN POWER "OFF", REVERSE ELECTRODE
AND WORK CABLE AT POWER SOURCE.
N.D. FOR WIRE FEEDERS THAT RETURN A SIGNAL FOR
WELDING OUTPUT, USE ISOLATION RELAY TO CLOSE
LEADS 2 & 4.
N.E. WELDER OUTPUT STUDS ON THE OPPOSITE SIDE
FOR CLASSIC II.
N.F. WHEN MACHINE IS IN "REMOTE" MODE, A REMOTE
OUTPUT CONTROL MUST BE CONNECTED.
N.G. IF MACHINE IS IN "LOCAL" MODE, ELECTRODE IS
ALWAYS "HOT".
( NOT USED ON
CLASSIC I)
TO
WORK
K867 UNIVERSAL
ADAPTER PLUG
TO
K867
TO
WIRE FEEDER
ENGINE WELDERS WITH WIRE FEED MODULE TO K867 UNIVERSAL ADAPTER
CONNECTION DIAGRAM: ALL CLASSIC, ALL PIPELINER, SA-250, 350SA & SAE-300
ENGINE
WELDER
Only qualified persons should install, use or
service this machine.
using the disconnect switch at the fuse box
WARNING
Turn off input power to the Welding Power Source
Before connecting the wire feeder.
ELECTRIC
SHOCK
CAN KILL
S 2 1 0 3 8
CV-
+
N.C.
ELECTRODE CABLE
TO LN-7
14 PIN
AMPHENOL
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.C.
76
82
81
SPARE
2
4
41
42
31
32
GND
21
77
75
REMOTE OUTPUT CONTROL
CONNECT TOGETHER FOR
WELDING OUTPUT
115 VAC / 2 AMP
}
}
}
N.D.
2
4
10K
MIN.
NOT USED
FRAME CONNECTION
}
NOT USED
NOT USED
}
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT
AND DUTY CYCLE OF APPLICATION.
N.B. DIAGRAM SHOWS ELECTRODE POSITIVE. TO CHANGE
POLARITY, TURN POWER "OFF", REVERSE ELECTRODE
AND WORK CABLE AT POWER SOURCE.
N.D. FOR WIRE FEEDERS THAT RETURN A SIGNAL FOR
WELDING OUTPUT, USE ISOLATION RELAY TO CLOSE
LEADS 2 & 4.
N.E. WELDER OUTPUT STUDS ON THE OPPOSITE SIDE
FOR CLASSIC II.
N.F. WHEN MACHINE IS IN "REMOTE" MODE, A REMOTE
OUTPUT CONTROL MUST BE CONNECTED.
N.G. IF MACHINE IS IN "LOCAL" MODE, ELECTRODE IS
ALWAYS "HOT".
( NOT USED ON
CLASSIC I)
TO
WORK
K867 UNIVERSAL
ADAPTER PLUG
TO
K867
TO
WIRE FEEDER
ENGINE WELDERS WITH WIRE FEED MODULE TO K867 UNIVERSAL ADAPTER
CONNECTION DIAGRAM: ALL CLASSIC, ALL PIPELINER, SA-250, 350SA & SAE-300
ENGINE
WELDER
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the
machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.