Filter
Top Products
Installation & Programming Manual FX & VFX “E” Series Inverte r/Charge r Sy ste m Copyright 2003 OutBack Power Systems, Inc.
19009 62
nd
Ave NE, Arlington WA 98223 USA
Page 44 Rev 7.0 07/02/04 Tel 360 435 6030 Fax 360 435 6019
MATE - ADVANCED MENU
The ADVANCED (ADV) menu section allows adjustment of all the settings involved with the operation of the FX. Changes made to
these settings are stored internally in non-volatile memory inside of the FX – the settings are not lost when the MATE is removed or
battery power is disconnect.
Some settings appear both in the SETUP and in the ADV menus. Changes made to these settings in one area will cause the same
changes to occur in the other area. The settings are provided in both menus to make it more convenient for the FX programmer by
giving access to all of the settings in the advanced menu.
Access to the settings in the ADV menu is restricted through the use of a password. This password is required to view and adjust the
settings. Once the password has been entered, all advanced categories can be adjusted without having to re-enter the password. If
the advanced menu is exited and re-entered, the password must be re-entered, however. Use of the “hot” keys AC IN and INV is
allowed from the advanced menu and selecting OK from these screens will return you to the same point in the advanced menu.
The password for the inverter is currently fixed to the same value for all of the FX’s.
PASSWORD CODE: 1 4 1
MAIN----------------
6:54:42P
SUM STATUS SETUP ADV
↓
ADV/SETTINGS/WARNING
changes made could
adversely effect
system performance
↓ ↓ ↓ ↓
ADV/PASSWORD--------
enter the password:
132
ENTER INC DEC EXIT
↓
ADV-----------------
choose product:
FX MX MATE MAIN
↓
ADV/FX/PAGE1--------
choose category:
ADV INV CHGR PG2
↓
ADV/FX/PAGE2--------
choose category:
PG1 GRID GEN PG3
↓
ADV/FX/PAGE3--------
choose category:
PG2 AUX STACK PG4
↓
ADV/FX/PAGE3--------
choose category:
PG3 SELL CAL MAIN
The MAIN screen is where the menu system starts. The four words in the bottom line of the
display correspond to the four buttons located below the display. The word in
BOLD on the bottom
line indicates the selection used to advance the display to the next screen. Pressing the left two
buttons simultaneously from anywhere in the menu will return you to this screen.
Selecting
<ADV> brings up a warning message. Please read the message. Pressing any of the
four keys below the display advances the display to the password screen.
Entering the correct password number is done by pressing the <INC> key to increase the
number or the
<DEC> key to decrease the number. Once the number shown matches the
password code, press the key below the word
<ENTER>. To leave the advanced menu area
without making any changes, press EXIT.
Following the password screen is a screen that allows selection of the OutBack product type.
Selecting
<FX> allows adjustment of the FX’s advanced programming. Selecting MX will allow
access to the advanced sections of any MX-60’s connected to the system (through a HUB).
Selecting MATE will allow access to the MATE’s advanced screens. Selecting MAIN returns the
user to the MAIN menu.
There are eight categories of settings in the FX:
INV Allows adjustment of the INVERTER settings and operation
CHGR Allows adjustment of the CHARGER settings and operation
GRID Allows adjustment of the AC input settings and operation if the FX’s input is set to GRID
GEN Allows adjustment of the AC input settings and operation if the FX’s input is set to GEN
AUX Allows adjustment of the AUX OUTPUT settings and operation
STACK Allows adjustment of the master/slave settings for multi-FX systems
SELL Allows adjustment of the Grid-Tie settings and operation
CAL Allows adjustment of the voltage calibration measurements to improve operation
Selecting ADV will send the user back one screen to the “choose product” screen in the advanced
menu. PG2 will advance the user to page 2 of the advanced menu. PG3 will advance the user to
page 3 of the advanced menu. PG4 will advance the user to page 4 of the advanced menu.
Selecting MAIN will return the user to the MAIN screen.