Filter
Top Products
3
20. DANGER: KEEP HANDS AW AY FROM CUTTING AREA. Keep hands away from blades. Do not reach
underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.
CAUTION: Blades coast after being turned off.
21. MAKE WORKSHOPCHILDPROOF with padlocks, master switches, or by removing starter keys.
22. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by
Porter-Cable may cause hazards or risk of injury to persons.
23. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
24. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter
only.
25. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.Don t leave tool until it comes to a
complete stop.
26. ALW AYS HOLD THE WORK FIRMLY against the fence and table. D O N O T perform any operation freehand.
27. W ARNING: ALW AYS keep hands out of path of saw blade. If the workpiece you are cutting would cause your
hand to be inside the t able hazard area (see section TABLE HAZARD AREA ), the workpiece should be
clamped in place before making cut.
28. NEVER use blades larger or smaller in diameter than recommended. Recommended size of blade is 10" in
diameter.
29. NEVER use blades recommended for operation at less than 6000 RPM.
30. USE the blade guard at all times.
31. NEVER reach around or behind saw blade.
32. TURN OFF SAW and MAKE SURE blade has come to a complete stop before removing or securing
workpiece, changing workpiece angle or changing the angle of the blade.
33. USE PROPER EXTENSION CORD. Make sure your extension is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause
a drop in line volt age resulting in loss of power and overheating. The t able in EXTENSION CORD SELECTION
shows the correct size to use depending on cord length and nameplate ampere rating of the tool. If in doubt, use
the next heavier gage. The smaller the gage number, the heavier the cord.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY RULES FOR COMPOUND SLIDE MITER SAW S
1. W ARNING: USE ONLY CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES BE
SURE THE HOOK ANGLE IS 5 DEGREES OR LESS. DO NOT USE BLADES WITH DEEP GULLETS AS
THEY CAN DEFLECT AND CONTACT GUARD.
2. W ARNING: Do not operate the miter saw until it is completely assembled and installed according to the instructions.
3.IF YOU ARE NOT thoroughly familiar with the operation of compound slide miter saws, obt ain advice from
your supervisor, instructor or other qualified person.
4. BE SURE blade is sharp, runs freely and is free of vibration.
5. ALLOWthe motor to come up to full speed before starting cut.
6. KEEP motor air slots clean and free of chip s.
7. ALW AYS MAKE SURE rotating t able is tight before cutting, even if the t able is positioned in one of the
positive stop s.
8. BE SURE blade and flanges are clean and that arbor screw is tightened securely.
9. USE ONLY blade flanges specified for your saw.
10. NEVER apply lubricant s to the blade when it is running.
11. ALW AYS CHECK the blade for cracks or damage before operation. Replace cracked or damaged blade
immediately.
12. ALW AYS KEEP the lower blade guard in place and operating properly.
13. MAKE SURE blade is not cont acting workpiece before switch is turned on.
14. NEVER LOCK the switch in the O N position.
15. IMPORTANT: After completing cut, release power switch and wait for coasting blade to stop before returning
saw to raised position.
16. DO NOT remove jammed or cut-off pieces until blade has stopped.
17. NEVER cut ferrous metals or masonry.