Filter
Top Products
??19.8E-:006A?@91:@?
8-01$19;B-8-:0:?@-88-@5;:
See figures 3-6.
&;>10A/1@41>5?7;2<1>?;:-85:6A>E
-8C-E?05?/;::1/@<8A32>;9<;C1>
?;A>/1.12;>1/4-:35:3.8-01?
'?5:3@41;>>1/@8-01
8-010591:?5;:? 4-3/8” (110mm) diameter
3/4” Arbor
MIN RPM 11,000/min
"!$& & The saw blade provided on this tool has a
carbide-tipped kerf width of .078” (2mm) and a plate (body)
thickness that is .047” (1.2mm) thick. When looking for a
replacement blade, select one with dimensions close to the
original blade. This information may not be printed on the
blades packaging. If not, check the manufacturers catalog
or website. Skil offers an extensive line of Premium-Quality
Professional Saw Blades that match the requirements for
this tool. You must select a blade with a kerf width of .061”
or more and a plate (body) thickness .057” or less (Fig. 3).
&;>10A/1@41>5?7;25:6A>E0;:;@
A?11D@>-@45:71>2?-C.8-01? The
kerf of the blade must be wider than .061”. Extra thin kerf
saw blades (less than .061”) may cause the work piece to
bind against the riving knife during cutting. It is
recommended that the kerf of the replacement blade used
on this saw be .061” or more.
&;>10A/1@41>5?7;25:6A>E0;:;@
A?1?-C.8-01?9-01C5@4-@45/7
.;0E<8-@1 If the replacement saw blade's plate thickness
is greater than .057”, the riving knife would not properly
serve as an aid to reduce kickback. The replacement
blade's plate thickness must be less than .057”.
4-:35:3@418-01
!& Clean blade of any excess oil before installation.
1. Slide the saw assembly back to its farest position. This is
the position in which the blade can be removed from
saw.
2. Using a phillips head screwdriver, remove the rear screw
on the blade bolt cover and rotate the cover clear of the
blade bolt.
3. Push and hold in the arbor lock to lock the blade in
place. Using the hex wrench (included), turn the blade
bolt clockwise to remove it.
!& The blade bolt has a left hand thread.
5. Remove the blade bolt and blade collar.
6. Remove blade by sliding it down through the kerf insert
and out through the underside of the table.
!& Inner washer does not need to be removed.
7. Install a 4-3/8" (110mm) blade.
!& Make sure the rotation arrow on the blade
matches the rotation arrow on the upper guard.
FIG. 4
FIG. 5
BLADE BODY PLATE
PLAQUE DU CORPS DE LA LAME
PLACA DEL CUERPO DE LA HOJA
MUST BE LESS THAN .057”
D
OIT ÊTRE DE MOINS DE 0,057 PO
DEBE SER MENOS DE 0.057 PULGADAS
KERF WIDTH
LARGEUR DE VOIE
ANCHURA DE LA SECCIÓN DE CORTE
RIVING KNIFE
COUTEAU DIVISEUR
CUCHILLA SEPARADORA
MUST BE .061” OR MORE
DOIT ÊTRE DE 0,061 PO OU PLUS
DEBE SER 0.061 PULGADAS O MÁS
.059”
BLADE TEETH
D
ENTS DE LA SCIE
DIENTES DE LA HOJA
FIG. 3
>.;>;/7
8-01;8@
;B1>
$;@-@5;:
>>;C
8-01%8;@
$;@-@5;:
;2.8-01
$19;B1-:0
5:?1>@.8-01@4>A
?8;@5:>1->;2@-.81
WARNING
!
WARNING
!
WARNING
!