Filter
Top Products
$%# !
Motor does not start.
(&
1. Check that unit is plugged in.
2. Power source fuse or
time delay fuse.
3. Brushes worn.
4. Other.
#%%')'#"
- Plug unit in. Use different
outlet.
- 15-Amp time delay fuse or
circuit breaker.
- See Motor Brush Replacement in
the Maintenance and Lubrication
section.
- Authorized service.
'?<B/92@5<<A6;4
'?<B/92@5<<A6;4B612920A?60.9
92.;6;4
'< .C<61 .00612;A@ .9D.F@
16@0<;;20A A52 A<<9 3?<: A52
=
<D2?@B==9F/23<?2092.;6;4<?=2?3<?:6;4.;F
:.6;A2;.;02 '52 A<<9 :.F /2 092.;21 :<@A
23320A6C29F D6A5 0<:=?2@@21 .6? 9D.F@ D2.?
@.32AF 4<4492@ D52; 092.;6;4 A<<9@ D6A5
0<:=?2@@21.6?
Ventilation openings and switch levers must be kept
clean and free of foreign matter. Do not attempt to
clean by inserting pointed objects through openings.
Check regularly to make sure the lower guard and all
moving parts are working properly.
Remove accumulated sawdust from working parts by
blowing with compressed air or wiping with a damp
cloth.
2?A.6; 092.;6;4 .42;A@ .;1
@<9C2;A@ 1.:.42 =9.@A60 =.?A@
&<:2 <3 A52@2 .?2 4.@<96;2 0.?/<;
A2A?.059<?612 059<?6;.A21 092.;6;4 @<9C2;A@
.::<;6..;15<B@25<9112A2?42;A@A5.A0<;A.6;
.::<;6.
.?2<39.12@
Blades become dull even from cutting regular lumber.
If you find yourself forcing the saw forward to cut
instead of just guiding it through the cut, chances are
the blade is dull or coated with wood pitch.
When cleaning gum and wood pitch from blade,
unplug the saw and remove the blade. Remember,
blades are designed to cut, so handle carefully. Wipe
the blade with kerosene or similar solvent to remove
t
he gum and pitch. Unless you are experienced in
sharpening blades, we recommend you do not try.
'<<9 B/?60.A6<;
$?2C2;A6C2 :.6;A2;.;02
=2?3<?:21 /F B;.BA5<?6G21
=2?@<;;29 :.F ?2@B9A 6; :6@=9.06;4 <3 6;A2?;.9
D6?2@ .;1 0<:=<;2;A@ D5605 0<B91 0.B@2
@2?6<B@ 5.G.?1 *2 ?20<::2;1 A5.A .99 A<<9
@2?C602/2=2?3<?:21/F.<@053.0A<?F&2?C602
2;A2?<?BA5<?6G21<@05&2?C602&A.A6<;
Your Bosch tool has been properly lubricated and is
ready to use. It is recommended that tools with gears
be regreased with a special gear lubricant at every
brush change.
Periodically lubricate moving parts with a silicone, or
light oil spray. Do not use grease because it tends to
attract and hold sawdust.
2.?6;4@
All bearings in this tool are lubricated with a sufficient
amount of high-grade lubricant for the life of the unit
under normal operating conditions. No further
lubrication is required.
*%""
!
*%""
!
!.6;A2;.;02.;1 B/?60.A6<;
*%""
!
BM 2610025580 05-13_BM CM8S 5/17/13 1:37 PM Page 42