Filter
Top Products
5-15
Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide
Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004
Chapter 5 Configuring the MGX RPM-PR
Verifying the Configuration
MA Test History :00
MA Test History :01
EPROM format version 4
EPROM contents (hex):
0x00:04 22 40 02 22 C0 46 03 20 00 1C 0A 02 82 49 13
0x10:90 02 42 42 30 C1 8B 53 42 4B 30 34 34 35 30 30
0x20:35 45 C6 8A 42 41 41 36 50 54 30 43 41 41 84 00
0x30:00 00 00 04 00 03 00 03 01 FF FF FF FF FF FF FF
0x40:04 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50:0A AA FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60:46 D6 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70:00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x80:44 03 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90:42 82 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xA0:0C 83 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xB0:00 C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0:40 41 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0:82 82 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0:2C AC FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x100:02 40 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x110:63 51 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x120:42 42 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x130:00 20 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x140:B8 17 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x150:0C C2 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x160:0C 2C FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x170:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x180:62 C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x190:82 6C FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1A0:D1 CE FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1B0:00 C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1C0:92 C8 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1D0:21 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1E0:0C 0C FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x1F0:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
See the next section, “Verifying Ethernet Connectivity,” to verify that each interface port is functioning
properly.
Verifying Ethernet Connectivity
The ping command lets you verify that an interface port is functioning and check the path between a
specific port and connected network devices. This section provides brief descriptions of the ping
command. After you verify that the system has booted successfully and is operational, you can use this
command to verify the status of interface ports. The remote device can be a server, a router, or a PC.
The ping command sends an echo request out to a remote device at an IP address that you specify. After
sending a series of signals, the command waits a specified time for the remote device to echo the signals.
Each returned signal is displayed as an exclamation point (!) on the console terminal; each signal that is
not returned before the specified time-out is displayed as a period (.). A series of exclamation points
(!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed]
indicate that the connection failed.
Following is an example of a successful ping command to a remote server with the address 1.1.1.10:
Router#ping 1.1.1.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.10, timeout is 2 seconds: