Filter
Top Products
CONNECTING POWER
• Ensure that the unit and power cord
are clean and dry.
• insert the round end of the power cord
connector into the jack in the back of
the unit.
• Plug the cord into an appropriate
electrical outlet.
Fuse block
Jack
Cord
REMOVING AND INSTALLING
DRAWERS:
• Empty the drawer.
• Fully extend the drawer.
Release
Lever Style - Lift or
lower (depending on the
slide) the release lever
on both sides, (this
allows the slides to ride
over the stops.) Pull out
to remove.
Tab Style - Depress the
release tabs on both
sides, (this allows the
slides to ride over the
stops.) Pull out to
remove.
To reinstall, carefully align the slides and
push the drawer into the unit until the
drawer stops.
INFORMATION CENTER
OPERATION
The information center is equipped with a
battery backup to maintain memory only.
The display will not function while power
is disconnected from the unit.
Outside temperature display requires
optional outside temperature sensor.
Display backlight
• Pressing _ turns the display
backlight on for 15 seconds.
Setting the current time
• Press and hold _ for at least
two seconds. (Second resets to zero
and hour begins to flash.)
• Press _ to set am/pm or 24 hour
mode as desired. Note: The am/pm
indicator is not shown in 24 hour
mode.
• Adjust hour using (_ and (_.
• Pressing _ toggles to next field.
Note: To toggle to minute without
changing hour, press _) then (_ then
• Adjust minute using (_ and (_.
• Press _ to toggle to next field.
• Repeat to adjust Month, Day, and
Year.
• Toggling past year exits set mode.
• Day of week is displayed according to
Month, Day, and Year.
Temperature Display
Pressing _ toggles inside and
outside temperature displays between
Celsius and Fahrenheit.
• Pressing _ toggles inside and
outside temperature displays between
ACT (Actual temperature)
MIN (Minimum recorded
temperature since last reset)
MAX (Maximum recorded
temperature since last reset)
• Press and hold _ for at least two
seconds to clear inside and outside
minimum and maximum recorded
temperatures.
• An audible beep will sound when
temperature is reset.
Setting the alarm
• Press and hold _ for at least
two seconds. (Second resets to zero
and hour begins to flash.)
• Adjust hour using (_ and (_).
• Pressing _ toggles to next field.
• Repeat to adjust minute.
• Toggling past minute exits set mode.
Turning alarm on or off
When the alarm is activated, the display
will show the indicator _,.
• Press _ to activate or deactivate
the alarm.
• Press _ to silence alarm when
ringing.
Timer function
• Press _ to enter timer mode.
• Press _ to start timer.
• Each time _ is pressed starts
or stops timer.
• Press and hold _ for at least
two seconds to reset timer to zero.
Count down timer function
• Press and hold _ for at least two
seconds.
• Display shows O0:O0:O0 and hour
begins to flash.
• Adjust hour using @ and @.
• Pressing @ toggles to next field.
• Repeat to adjust minute and second.
• Toggling past second exits set mode.
Note: To set timer to 24 hours, toggle
display to 00:00:0O.
• Press _ to start count down.
• Each time _ is pressed starts
or stops timer.
• Alarm sounds when timer reaches
0O:00:OO.
• Press any button to silence the alarm.
Clock
When in Timer or Count down timer
mode, press _ to display current
time. Press _ to return to timer
or
count down timer.
oF_eoCP_
Clock Set
Alarm Set-_
(+)
(-)
Time
\
• \\
D
Temp Inside
AM/PM
\ \
\ \
Date
Alarm
Activated
jTimer
Start/Stop
Clock
Alarm
Light
Temp outside
(Accessoryrequired)
5 6