Filter
Top Products
&!'
&*"(P)#(
GND
75
76
77
GREEN
K291 OR K404
75
INPUT CABLE
76
N.E.
77
K775 OPTIONAL
REMOTE CONTROL
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
81
42
41
31
31
32
32
2
2
4
4
21
21
GND
82
N.D.
LN-7
WIRE
FEEDER
Keep guards in place.
ENGINE WELDERS / K867 / K775 / LN-7 CONNECTION DIAGRAM
Keep away from moving parts.
WARNING
Only qualified personnel should install,use
or service this equipment.
SPARE
Do not operate with panels open.
7-2000
S23983
Disconnect NEGATIVE (-) BATTERY LEAD
ELECTRODE
ELECTRODE CABLE
TO WIRE FEED UNIT
K867 UNIVERSAL
ADAPTER PLUG
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
THE ENGINE WELDER OPERATING MANUAL.
N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
APPILICATIONS. SEE OPERATING MANUAL.
PLACE WIRE FEEDER SWITCH TO "WIRE FEEDER WITH CONTROL CABLE POSITION.
N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE "SELECTOR" SWITCH TO "WIRE WELDING CV".
N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED,CONTROL IS AUTOMATICALLY SWITCHED TO REMOTE CONTROL.
N.D. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.E. SPLICE LEADS AND INSULATE.
}
before servicing.
Do not touch electrically live parts.
}
14 PIN
AMPHENOL
TO WORK
TO WORK
GND
75
76
77
GREEN
K291 OR K404
75
INPUT CABLE
76
N.E.
77
K775 OPTIONAL
REMOTE CONTROL
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
81
42
41
31
31
32
32
2
2
4
4
21
21
GND
82
N.D.
LN-7
WIRE
FEEDER
Keep guards in place.
ENGINE WELDERS / K867 / K775 / LN-7 CONNECTION DIAGRAM
Keep away from moving parts.
WARNING
Only qualified personnel should install,use
or service this equipment.
SPARE
Do not operate with panels open.
7-2000
S23983
Disconnect NEGATIVE (-) BATTERY LEAD
ELECTRODE
ELECTRODE CABLE
TO WIRE FEED UNIT
K867 UNIVERSAL
ADAPTER PLUG
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
THE ENGINE WELDER OPERATING MANUAL.
N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
APPILICATIONS. SEE OPERATING MANUAL.
PLACE WIRE FEEDER SWITCH TO "WIRE FEEDER WITH CONTROL CABLE POSITION.
N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE "SELECTOR" SWITCH TO "WIRE WELDING CV".
N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED,CONTROL IS AUTOMATICALLY SWITCHED TO REMOTE CONTROL.
N.D. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.E. SPLICE LEADS AND INSULATE.
}
before servicing.
Do not touch electrically live parts.
}
14 PIN
AMPHENOL
TO WORK
TO WORK