Filter
Top Products
-23-
N(/(*(/Fg\e<e[N`[\9\ckJXe[\i
FG<I8K@FEJ
JXe[`e^9\ckFjZ`ccXk`fe
IXk\
To prevent sanding "streaks" in the workpiece and ensure
an even finish, the sanding belt oscillates from side-to-
side on the sanding drum during operation. This action is
caused by the twisting motion of the upper sanding roller
that causes the sanding belt to shift along the roller until
it hits the oscillation disc at the end, which then causes
the sanding belt to reverse direction to the other end.
We recommend that one oscillation cycle (the movement
of the sanding belt from one side to the other) should be
approximately 4–6 seconds.
Efk\1Pfln`cc_\XiXd\kXcc`Zk_ldgn_\ek_\jXe[`e^
Y\ckZ_Xe^\jfjZ`ccXk`fe[`i\Zk`fe%K_`jef`j\`jefidXc%
KffcjE\\[\[ Hkp
Wrench 12mm ................................................... 1
KfX[aljkk_\jXe[`e^Y\ckfjZ`ccXk`feiXk\#[fk_\j\
jk\gj1
(% DISCONNECT THE SANDER FROM POWER!
)% Open the sanding belt access door and identify the
oscillation stops shown in =`^li\)*.
*% Loosen the oscillation stop jam nuts, then adjust the
oscillation stop hex bolts equally in or out to change
the oscillation rate.
Efk\1K_\fjZ`ccXk`feiXk\`jk_\k`d\`kkXb\jk_\
jXe[`e^Y\ckkfdfm\]ifdfe\j`[\f]k_\lgg\i
jXe[`e^ifcc\ikfk_\fk_\ij`[\Xe[_`kk_\fjZ`ccX$
k`fe[`jZXkk_\\e[%<XZ__\oYfckj\kk`e^X]]\Zkj
k_\fjZ`ccXk`feiXk\`efe\[`i\Zk`fe%K`^_k\e`e^X
jkfg_\oYfckn`ccZXlj\Xjcfn\ifjZ`ccXk`feiXk\]fi
k_Xk[`i\Zk`fe%<og\i`d\ekkf]`e[k_\i`^_kfjZ`ccX$
k`feiXk\]fipflifg\iXk`fe%
+% Re-tighten the jam nuts without turning the hex
bolts, then close the access door.
,% Connect the machine to power, start the sanding
motor, then check the oscillation rate.
-% Repeat Jk\gj(Æ, until you are satisfied with the
oscillation rate.
=`^li\)*% Sanding belt oscillation stops.
Stops
Jam Nut
Hex Bolt
Jam Nut
Hex Bolt
NOTICE
K_\ jXe[`e^ Y\ck fjZ`ccXk`fe jpjk\d
i\hl`i\jXjfliZ\f]Zc\Xe#[ipZfd$
gi\jj\[ X`i Zfee\Zk kf k_\ dXZ_`e\
Xe[X[aljk\[kf,.Æ-'GJ@%N`k_flkk_`j
iXk\f]Zfdgi\jj\[X`i#k_\jXe[\in`cc
efkfg\iXk\%