Filter
Top Products
15
WAGNER Project Pro 117 - 0418B
Components and Description
The shipping carton for your painting system contains the following:
• Suctiontubeandreturntube(includinginletlterand3clips) •Spraytipassembly
• Basicunit •7.5m,6.35mminternaldiameterpressurehose
• Spraygunwithtwolters(L-XXL;oneingun,oneseparate) •Oilask
• Instructionmanual
Figure 1 - Controls and Functions
(further, detailed descriptions of the individual items can be found in the relevant section of the operating instructions)
Item Component Description
A) ON / OFF Switch ............................The ON/OFF switch turns the power to the sprayer on and o (O=OFF, l=ON).
B) PRIME / SPRAY Knob ....................The PRIME/SPRAY knob directs uid to the spray hose when set to SPRAY or the return tube when set
to PRIME. The arrows on the PRIME/SPRAY knob shows the rotation directions for PRIME and SPRAY.
The PRIME/SPRAY knob is also used to relieve pressure built up in the spray hose (see Pressure Relief
Procedure).
C) Quicko™ Valve .............................The Quicko™ valve is designed to keep the inlet valve open and from sticking to dried materials.
The Quicko™ valve is activated manually by the user.
D) PressureTrac™ ................................The PressureTrac™ regulates the amount of force the pump uses to push the uid.
E) Pump Section .................................A piston in the pump section moves up and down to create the suction that draws uid through the
suction tube.
F) Suction Tube ..................................Fluid is drawn through the suction tube into the pump.
G) Return Tube ....................................Fluid is sent back out through the return tube to the original container when PRIME/SPRAY knob is in
PRIME position.
H) Inlet lter ..........................................The inlet lter strains the spray material to prevent the system from becoming clogged.
I) Spray Gun ........................................For application of the coating material and regulation of the pump capacity.
J) Spray Hose ......................................The spray hose connects the gun to the pump.
When working outdoors:
Danger
Vapors containing solvents may not be allowed to
blow toward the unit.
Note the direction of the wind.
Set the unit up in such a way that vapors containing
solvents do not reach the unit and build up there.
A minimum distance of 5 m between the unit and
spray gun is to be maintained.
U Cleaning the unit
Danger
Danger of short circuit through penetrating water!
Never spray down the unit with high-pressure or
high-pressure steam cleaners.
U Cleaning units with solvents
Danger
When cleaning the unit with solvents, the solvent
should never be sprayed or pumped back into a
container with a small opening (bunghole). An
explosive gas/air mixture can be produced. The
container must be earthed.
Do not clean the device or accessories with
ammable solvents with a ash point below 21 °C.
U Earthing of the object
The object to be coated must be earthed.
Technical Data
Pump type Piston pump
Power source 230-240 V
~
50 Hz
Power consumption 670 W
Fusing
Only connect to sockets protected
with an FI fuse (16 A)
Double insulation
Max. spray pressure 200 bar
Max. delivery rate 1,0 l/min
Sound pressure level 71,4 dB (A)
Oscillation level < 2,5 m/s²
Max. temperature of coating
substance
40°C
Max. nozzle size XL (0,019")
Hose length 7,5 m
Weight 7,8 kg
Coating Materials Suitable for Use
Water-based and solvent-containing lacquers and glazes.
Paints, oils, release agents, synthetic enamels, PVC lacquers,
undercoats, base coats, llers and anti-rust paints.
Dispersion and latex paints for interior use.
Coating Materials Not Suitable for Use
Materials that contain highly abrasive components, facade paint,
caustic solutions and acidic coating substances.
Materials with a ash point below 21°C.
i
In order to ensure compatibility of the coating substance
with the materials used to manufacture the device, please
contact Wagner Service in cases of doubt.