Filter
Top Products
8 9
Accessory
order number
Accessories supplied
Remarks
Speed settings
Motor size (mm)
Output drive tool-
holding fixture
Weight withouth calbe (kg)
Nominal current (A)
Nominal power
output (W)
Nominal power
consumption (W)
Idling
speed (min
-1
)
Max. bit-
l
in aluminium (mm)
Max. bit-
l
in steel (mm)
Frequecy (Hz)
Voltage (V)
Order number
DRILLS.
The suitable drills for a very wide
variety of materials
Drill at constant speed for opti-
mised operational life
Motors with extremely long service
lives for economical work
HBM 55/1
0 602 120 101 265 200 3
0 602 120 104 135 200 3
0 602 120 107 72 200 3
0 602 120 104 200 300 2
0 602 121 101 265 200 6
0 602 121 104 135 200 6
0 602 121 107 72 200 6
0 602 121 104 200 300 4
3 608 571 0017 2450 260 150 0.9 1.7 1/2
HH-20 UNF 55 1
7 2450 260 150 1.7 1.7 1/2
HH-20 UNF 55 1
7 2450 260 150 3.2 1.7 1/2
HH-20 UNF 55 1
7 3700 400 230 1.7 1.7 1/2
HH-20 UNF 55 1
9 1350 260 140 0.9 1.7 1/2
HH-20 UNF 55 1
9 1350 260 140 1.7 1.7 1/2
HH-20 UNF 55 1
9 1350 260 140 3.2 1.7 1/2
HH-20 UNF 55 1
9 2000 400 230 1.7 1.7 1/2
HH-20 UNF 55 1
1-speed drill
with three-jaw chuck
Chuck with key
Clamping range 1–10 mm
HBM 57/1
0 602 131 101 265 200 6
0 602 131 104 135 200 6
0 602 131 107 72 200 6
0 602 131 104 200 300 4
0 602 133 101 265 200 9
0 602 133 104 135 200 9
0 602 133 107 72 200 8
0 602 133 104 200 300 8
0 602 134 101 265 200 2
3 608 571 001
3 608 571 004
10 1350 470 310 1.6 2.0 1/2HH-20 UNF 57 1
10 1350 470 310 3.3 2.0 1/2
HH-20 UNF 57 1
10 1350 470 310 6.1 2.0 1/2HH-20 UNF 57 1
10 2050 600 400 3.3 2.0 1/2
HH-20 UNF 57 1
10 690 470 310 1.6 2.0 1/2
HH-20 UNF 57 1
10 690 470 310 3.3 2.0 1/2
HH-20 UNF 57 1
10 1000 400 310 6.1 2.0 1/2
HH-20 UNF 57 1
10 1030 700 460 3.3 2.0 1/2
HH-20 UNF 57 1
6 3300 400 270 1.6 2.0 M 13 x 1 57 1
1-speed drill
with three-jaw chuck
1-speed drill with keyless
chuck
Chuck with key
Clamping range 1–10 mm
HBM 57/2
0 602 135 001 265 200 5/3
0 602 135 004 135 200 5/3
0 602 135 101 265 200 8/5
0 602 135 104 135 200 8/5
0 602 135 104 200 300 5/4
3 608 571 00110/8 1600/2400 400 270 1.6 2.0 1/2
HH-20 UNF 57 2
10/8 1600/2400 400 270 3.3 2.0 1/2
HH-20 UNF 57 2
10/8 900/1500 400 270 1.6 2.0 1/2
HH-20 UNF 57 2
10/8 900/1500 400 270 3.3 2.0 1/2
HH-20 UNF 57 2
10/8 1500/2200 600 400 3.3 2.0 1/2
HH-20 UNF 57 2
2-speed drill
with three-jaw chuck
Chuck with key
Clamping range 1–10 mm
HBM 65/1
0 602 117 001 265 200 13
0 602 117 004 135 200 13
0 602 117 008 72 200 13
0 602 117 004 200 300 10
1 608 571 027
1 602 025 022
13 510 600 440 1.6 2.8 Taper B 16 65 1
13 510 600 440 3.3 2.8 Taper B 16 65 1
13 510 600 440 5.9 2.8 Taper B 16 65 1
13 760 900 630 3.3 2.8 Taper B 16 65 1
1-speed drill with
speed handle.
Three-jaw chuck can be
ordered as a special
accessory.
Chuck
Clamping range 1.5–13 mm
Additional handle
HBM 77/2
0 602 119 001 265 200 16/12
0 602 119 004 135 200 16/12
0 602 119 008 72 200 16/12
0 602 119 004 200 300 16/18
1 600 763 010
3 601 030 002
23 216/512 950 700 2.8 5.6 Morse Taper2 77 2
23 216/512 950 700 5.5 5.6 Morse Taper2 77 2
23 216/512 950 700 10.0 5.6 Morse Taper2 77 2
23 328/775 1450 1050 5.5 5.6 Morse Taper2 77 2
2-speed drill with
cross handle.
Without chuck.
Suitable for bits with.
morse taper 2.
Three-jaw chuck can be
ordered as a special
accessory.
Tubular handlef (M 27 x 2)
Drill drift
The machines come equipped with a special 4-m-long cable without plug. Your specialist dealer can provide you with information on the complete set of quality accessories.