Filter
Top Products
GENERAL SAFETY mNSTRUCTmONS
BEFORE USING THIS DRILL PRESS
Safety is a combination of common sense, stay alert
and knowing how to use your dril! press.
[AWARN NGI
To avoid mistakes that could cause serious injury,
do not plug the drill press in until you have read and
understood the following.
1. READ and become familiar with the entire instruction
manual. LEARN the tool's application, limitations and
possible hazards.
2. KEEP GUARDS tN PLACE and in working order.
3. DON'T USE tN DANGEROUS ENVIRONMENT.
Don't use power tools in damp and wet locations, or
expose them to rain. Keep work area well lighted.
4. DO NOT use power tools in the presence of
flammable liquids or gases.
5. KEEP WORK AREA CLEAN. Cluttered areas and
benches invited accidents.
6. KEEP CHILDREN AWAY. All visitors should be kept
safe distance from work area.
7. DON'T FORCE THE TOOL. It wi!l do the job better
and safer at the rate for which it was designed.
8. USE THE RIGHT TOOL. Do not force a tool or an
attachment to do a job for which it was not designed.
9. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
10.WEAR A FACE MASK OR DUST MASK. Sawing
operation produces dusL
11.DISCONNECT TOOLS before servicing; when
changing accessories such as blades, bits, cutters,
and the like.
12REDUCE THE RiSK OF UNINTENTIONAL
STARTING. Make sure the switch is in the off
position before plugging in.
1&USE RECOMMENDED ACCESSORIES. Consult
the owner's manual for recommend accessories. The
use of improper accessories may cause risk of injury
to persons.
14.REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from the too! before turning it
ON.
15NEVER LEAVE A TOOL RUNNING UNATTEND.
TURN THE POWER "OFF". Don't leave the tool until
it comes to a complete stoG
16NEVER STAND ON THE TOOL. Serious injury
could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
17DON'T OVERREACH. Keep proper footing and
balance at al! times.
18.1VIAtNTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
1&CHECK FOR DAMAGED PARTS. Before further
use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function
= check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced.
2&MAKE WORKSHOP CHILD PROOF with pad!ocks,
master switches, or by removing starter key&
21 .DO NOT operate the tool if you are under the
influence of any drugs, alcoho! or medication that
could affect your ability to use the tool properly.
22.Dust generated from certain materiai can be
hazardous to your health. Always
W_AR YOUR
operate the drill press in a well-
ventilated area and provide for
proper dust removal. Use a dust
collection system whenever
possibb.
2&ALWAYS WEAR EYE PROTECTION. Any drill
press can throw foreign objects into the eyes and
could cause permanent eye damage. ALWAYS
wear Safety Goggles (not glasses) that comply with
ANSi Safety standard Z87.1 Everyday eyeglasses
have only impact -resistance lenses. They ARE
NOT safety glasses. Safety Goggles are available at
Sears. NOTE: Glasses or goggles not in compliance
with ANSI Z87.1 could seriously hurt you when they
break.