Filter
Top Products
unpacking
Qnd checking
TABLE OF LOOSE PARTS
The Following Parts Are Included With
Model 113.206930 Only
Item
No. Description Qty.
A Leg .............................. 4
B End Stiffener ........................ 2
C Side Stiffener ...................... 4
D Motor Support ..................... !
E Motor ............................ I
Package of Miscellaneous Small Parts,
No. 67035, Consisting of the Following:
F Cord Clip .......................... 2
G Hex Nut, 1/4 in. - 20
(approx. dia. of hole 1/4 in.) .......... 40
G Hex Nut, 5/16 in. - 18
(approx. alia. of hole 5/1 6 in.) ......... 7
G Hex Nut, 1/2 in. - 13
(approx. dia. of hole 1/2 in.) .......... 8
H Truss Hd. Screw, 1/4 in. - 20 x 5/8 in.
tong. (Top of screw is rounded) ........ 40
J Flat Washer (dia. of hole 11/32 in.) ...... 7
K Lockwasher, 1/4 in. External Type
(approx. alia. of hole t/4 in.) .......... 40
K Lockwasher, 5/16 in. Externa_ Type
(approx. dia. of hole 5/16 in.) ......... 7
L Carriage Bolt, 5i16in.- 18x3/4tong ... 3
M Leveling Foot ...................... 4
N Hex Hd. Screw, 5/16 in. - 18x 2in ..... 3
contents
F
G H
©
K
E
L M
ill , i ill i
assembly
ASSEMBLING STEEL LEGS
NOTE: Steel Legs are furnished with Model 113.206930.
From among the loose parts, find the following Hardware:
40 Truss Head Screws, 1/4-20 x 5/8
40 Lockwashers, 1/4-External
40 Hex Nuts, 1/4-20
8 Hex Nuts, 1/2-t3
4 Leveling Feet
1. Assemble two (2) Side Stiffeners together using four (4)
1/4-20 Truss head screws, Iockwasher and nuts. Make
two (2) Side Stiffener assemblies.
The End Stiffeners are placed on top and at each end of
Side Stiffener assemblies as shown. Atign holes, tetter
coded "B °' in Side Stiffeners and End Stiffeners and
then insert t/4-20 Truss head screws through the 9/32
diameter holes letter coded "C" and install lockwashers
and nuts and then tighte_n.
2. Assemble the four (4) Legs to the Side and End
Stiffeners using t/4-20 screws, lockwashers and nuts as
shown,
3. Assemble the Motor Support to the Legs with t/4-20
screws, lockwashers and nuts. Motor Support can be
assembled to either end of Leg set.
4. Install leveting feet as shown. To level Leg Set, loosen
nut on inside of leg and tL_rn nut on the outside to raise
or lower feet. Adjust all four leveling feet, if necessary,
and then tighten nuts o_ the inside of leg.
NOTE: These levelers are not intended for height
adjustment.
TRUSS HD. SCREW END STIFFENER
1/4-20 x 5/8
1/4 EXTERNAl-
LOCKWASHER
END
STIFFENER
..... 1/4-20 HEX
IDE STIFFENERS
° 'i
"i'"_J MOTOR SUPPORT
/ _i_ _i LEGS
i E
'i
f
LEGS