Filter
Top Products
-14-
Df[\cN(/(0&N(/)'D]^%J`eZ\('&('
J8=<KP
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting
or operating this machine.
8iYfi1 A metal shaft extending from the drive
mechanism that is the mounting location for
the saw blade.
9\m\c:lk1 A cut made with the blade tilted to
an angle between 0˚ and 45˚ to cut a beveled
edge onto a workpiece. Refer to GX^\ +* for
more details.
9cX[\ >lXi[ 8jj\dYcp1 Metal or plastic safety
device that mounts over the saw blade. Its
function is to prevent the operator from com-
ing into contact with the saw blade. Refer to
GX^\*- for more details.
:ifjjZlk1 Cutting operation in which the crosscut
fence is used to cut across the shortest width
of the workpiece. Refer to GX^\ +( for more
details.
;X[f9cX[\1 Blade or set of blades that are used
to cut grooves and rabbets. Refer to GX^\ *+
for more details. ;FEFKlj\X[X[fYcX[\
cXi^\i k_Xe/`e [`Xd\k\ifek_`j jXn The
saw and arbor are not intended to safely use a
larger dado blade.
;X[f :lk1 Cutting operation that uses a dado
blade to cut a flat bottomed groove into the
face of the workpiece. Refer to GX^\ ++ for
more details.
=\Xk_\iYfXi[1 Safety device used to keep the
workpiece against the rip fence and against
the table surface. Refer to GX^\ ,, for more
details.
B\i]1 The resulting cut or gap in the workpiece
after the saw blade passes through during a
cutting operation.
B`ZbYXZb1 An event in which the workpiece is
propelled back towards the operator at a high
rate of speed.
Efe$K_ifl^_:lk1 A cut in which the blade does
not cut through the top of the workpiece.
Refer to GX^\*) for more details.
GXiXcc\c1 Being an equal distance apart at every
point along two given lines or planes (i.e. the
rip fence face is parallel to the face of the saw
blade).
G\ig\e[`ZlcXi1 Lines or planes that intersect and
form right angles (i.e. the blade is perpendicu-
lar to the table surface).
Glj_ Jk`Zb1 Safety device used to push the
workpiece through a cutting operation. Used
most often when rip cutting thin workpieces.
Refer to GX^\,/ for more details.
IXYY\k1 Cutting operation that creates an L-shaped
channel along the edge of the workpiece. Refer
to GX^\+. for more details.
I`g:lk1 Cutting operation in which the rip fence
is used to cut across the widest width of the
workpiece. Refer to GX^\+' for more details.
I`m`e^ Be`]\1 Metal plate located behind the
blade. It maintains the kerf opening in the
wood when performing a cutting operation.
Refer to GX^\*/ for more details.
JkiX`^_k\[^\1 A tool used to check the flatness,
parallelism, or consistency of a surface(s).
K_`eB\i]9cX[\1A blade with a kerf or thickness
that is thinner than a standard blade cannot be
used on this saw.
K_ifl^_:lk1 A cut in which the blade cuts com-
pletely through the workpiece. Refer to GX^\
*) for more details.
>cfjjXipf]K\idj