Lincoln LN-742 Welder User Manual


 
C-5
ACCESSORIES
C-5
K377 SMALL MOUNTING STAND FOR
READI-REEL COILS AND 22 TO 30 LB
SPINDLE WITH 2 IN. I.D.
This assembly includes a wire reel spindle (similar to
the K162 spindle) attached to a small frame. The unit
is supplied with the K363 Readi-Reel Adapter for using
the Lincoln Readi-Reel Electrode Coils. Without the
adapter the unit is capable of handling spools with a
2 in. I.D., a 12 in. maximum O.D., and a 4 in. width. For
spools with an 8 in. O.D., a K468 spindle adapter is
available. The spindle has an adjustable braking
system. See Attaching the Wire Reel Stand
procedure at the end of this section for installation
procedures.
K378 SMALL MOUNTING STAND FOR
13 TO 14 LB INNERSHIELD COILS
This assembly includes the same smaller frame as
used in the K377 and the fully enclosed canister
system for dereeling of the 14 lb coil. This system has
a fixed brake for the 14 lb coil. See Attaching the Wire
Reel Stand Procedure at the end of this section for
installation procedures.
K435 SPINDLE ADAPTER FOR
14 LB COILS
Permits 14 lb (6 kg) Innershield coils to be mounted on
2 in. (51 mm) O.D. spindles. For K377 and K445, or
K303 and K376 with optional K162H adapter.
K438 50 TO 60 LB READI-REEL ADAPTER
Adapts Lincoln Readi-Reel coils of 50 to 60 lb (22.7 to
27.7 kg) to a 2 in. (51 mm) spindle. (Included with
K445.)
K445 MOUNTING STAND FOR READI-
REEL COILS AND 50 TO 60 LB SPINDLE
WITH 2 IN. O.D.
50 to 60 lb (22.7 to 27.7 kg) Readi-Reel mounting
stand. This assembly includes framework that a 2 in.
(51 mm) O.D. spindle with adjustable brake and 50 to
60 lb (22.7 to 27.7 kg) (K438) Readi-Reel adapter.
Includes a lift bail and cable clamp for fastening the
input cable assembly. Does not include a dust shield.
A dust shield that covers the wire reel and protects the
wire from falling dirt and dust is available for this unit.
Order part number S14543. This unit will accept the
M11514 door kit (see K303) but only if already
equipped with optional dust shield (S14543).
K468 SPINDLE ADAPTER FOR
8 IN. O.D. SPOOLS
Permits 8 in. (203 mm) O.D. spools to be mounted on
2 in. (51 mm) O.D. spindles. For K377 and K445, or
K303 and K376 with optional K162H adapter.
M11514 WIRE REEL DUST SHIELD DOOR
FOR K303 AND K376
In extremely dusty and dirty locations this door kit can
be added to those units having the dust shield kit
(S14543). This door kit includes a hinged door and
sliding bottom seal. When these parts are attached to
the reel support per the instructions included, the unit
becomes a completely enclosed housing. Order part
no. M11514.
S14543 WIRE REEL DUST SHIELD FOR
K376 50 TO 60 LB WIRE REEL MOUNTING
STAND
A shield is available to cover the wire and reel to
protect the wire from falling dirt and dust. Order part
no. S14543. Instructions are provided with the kit.
ATTACHING THE WIRE
REEL STAND
The mounting hardware for mounting the stands is
included with the LN-742. Screws and washers are
inserted in their respective mounting holes. To
connect:
1. Remove the three 3/8 in. hex head bolts from the
back of the wire feed unit.
2. Place the wire reel mounting stand mounting
bracket in position against the back of the wire
feed unit.
3. Replace and tighten the hex head bolts. The long
screw and plain washer go into the top hole.
LN-742 & LN-742H