Grizzly T25920 Lathe User Manual


  Open as PDF
of 48
 
Model T25920/T25926 (Mfd. Since 08/14)
-43-
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
T25920/T25926 Labels & Cosmetics
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
T25920 Label Placement Front
(11/19/14)
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
T25920 Label Placement Back
(11/19/14)
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
WARNING!
Always wear
ANSI-approved safety
glasses and face shield
when using this
machine.
EYE/FACE INJURY
HAZARD!
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
MODEL T25920
12" X 18" VARIABLE-SPEED WOOD LATHE
Motor: 3/4 HP, 110V, 1-Ph, 60 Hz, 5.3A
Spindle Speeds: 650 – 3800 RPM
Distance Between Centers: 16-1/2"
Swing Over Bed: 12"
Swing Over Tool Rest: 9-1/2"
Spindle Size: 1" x 8 TPI RH
Spindle & Tailstock Taper: MT#2
Weight: 84 Lbs.
Specifications
Mfd. for Grizzly in China
Date
S/N
WARNING!
T25920 Machine Labels (A)
(11/19/2014)
• Size = 1:1
(unless otherwise noted)
• Labels MUST be made of
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL!
Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
grizzly.com
To reduce risk of serious personal injury while using this machine:
1. Read and understand manual before starting.
2. Always wear safety glasses, face shield, and respirator.
3. DO NOT wear loose clothing, gloves, jewelry; tie back long hair.
4. Properly set up lathe and tighten all locks before operating.
5. Rotate workpiece by hand before applying power.
6. DO NOT turn split workpieces or those containing knots.
7. Rough out workpiece before mounting.
8. Use lowest speed when starting a new workpiece.
9. Always support cutting tool on properly adjusted tool rest.
10. Disconnect power before setting up, adjusting, servicing lathe.
11. DO NOT operate when tired or under influence of drugs/alcohol.
12. DO NOT expose to rain or use in wet locations.
13. Prevent unauthorized use by children or untrained users.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
DANGER
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
WARNING
CAUTION
PANTONE 109 C
COLOR CODES
GRIZZLY BEIGE
PANTONE 7527 C
GRIZZLY LOGO RED
PANTONE 711C or RAL 3020
NOTICE
PANTONE 3005 C or RAL 5005
NOTICE
Check carbon brushes inside
motor regularly to avoid damage
to machine during operation.
65x143.5mm
17 x 19mm
22.5 x 56.5mm
26 x 228mm
120 x 72mm
38 x 71mm
REF PART # DESCRIPTION REF PART # DESCRIPTION
85 PT25920085 MACHINE ID LABEL (T25920) 88 PT25920088 SHOCK HAZARD LABEL
85 PT25926085 MACHINE ID LABEL (T25926) 89 PT25920089 ELECTRICITY LABEL
86 PT25920086 GRIZZLY.COM LABEL 90 PT25920090 CARBON BRUSHES NOTICE LABEL
87 PT25920087 SAFETY WARNING LABEL 91 PT25920091 GRIZZLY GREEN TOUCH-UP PAINT
85
86
87
88
89
9091
 previous next