Filter
Top Products
$)./''/$*)
+*2 -21 V
J>?I
;DJ?H;?DIJ7BB7J?EDI;9J?ED8;<EH;OEKIJ7HJ?DIJ7BB7
J?ED
' /-$.#*&97DA?BB
3(&2+/&$!$ * ,-)(( &-#)/&
* ,!),'.#$-$(-.&&.$)(
3 /,(.# $(*/.*)0 ,..#
$-)(( .-0$.#),!/- )1 !), 0),%$(")(
.#$- +/$*' (. /,()!! .# $(*/. *)0 ,.) (2
).# , +/$*' (.)(( . .).# 0 &$("-2-. '
..# $-)(( .-0$.#),!/- )1 !), 0),%
$(")(.# +/$*' (.
3)()..)/# & .,$&&2#).*,.-
3&02-)(( . .# +*2 - 21 V
",)/($(" &/"&). $(-$ .# , )(( .
$(*/. --)), .) *,)* ,-! .2 ,.#
",)/(
------------------------------------------------------------------------
The POWER WAVE® C300 will operate in harsh environ-
ments. Even so, it is important that simple preventative
measures are followed in order to assure long life and reli-
able operation.
• The machine must be located where there is free circula-
tion of clean air such that air movement in the back, out
the sides and bottom will not be restricted.
• Dirt and dust that can be drawn into the machine should
be kept to a minimum. The use of air filters on the air
intake is not recommended because normal air flow may
be restricted. Failure to observe these precautions can
result in excessive operating temperatures and nuisance
shutdown.
• Keep machine dry. Shelter from rain and snow. Do not
place on wet ground or in puddles.
• Do not mount the POWER WAVE® C300 over com-
bustible surfaces. Where there is a combustible surface
directly under stationary or fixed electrical equipment,
that surface shall be covered with a steel plate at least
.060” (1.6mm) thick, which shall extend not less than
5.90” (150mm) beyond the equipment on all sides.
Both handles should be used when lifting POWER WAVE®
C300. When using a crane or overhead device a lifting strap
should be connected to both handles. Do not attempt to lift
the POWER WAVE® C300 with accessories attached to it.
Do not weld with the POWER WAVE® C300 while the
machine is suspended by the handles.
The POWER WAVE® C300 cannot be stacked.
Place the machine directly on a secure, level surface or on
a recommended undercarriage. The machine may topple
over if this procedure is not followed.
Only a qualified electrician should connect the POWER
WAVE® C300. Installation should be made in accordance
with the appropriate National Electrical Code, all local
codes and the information in this manual.
The frame of the welder must be grounded. A ground ter-
minal marked with a ground symbol is located next to the
input power connection block.
See your local and national electrical codes for proper
grounding methods.
The EMC classification of the POWER WAVE® C300 is
Industrial, Scientific and Medical (ISM) group 2, class A.
The POWER WAVE® C300 is for industrial use only. (See
& .,)'"( .$)'*.$$&$.2! .2 .$)().
Locate the POWER WAVE® C300 away from radio con-
trolled machinery. The normal operation of the POWER
WAVE® C300 may adversely affect the operation of RF
controlled equipment, which may result in bodily injury or
damage to the equipment.
U'?<JEDBOM?J>;GK?FC;DJE<7:;GK7J;
B?<J?D=97F79?JO
U ;IKH;C79>?D;?IIJ78B;M>;DB?<J?D=
UEDEJEF;H7J;C79>?D;M>?B;IKIF;D:
;:M>;DB?<J?D=
!''$)"
,0$+( )/97D
97KI;?D@KHO
-----------------------------------------------------------------------------------------------