Filter
Top Products
*+ -/$*)
./ ') ./$)' .. "(2+
+0'. ($"2 '$)"
+*2 -21 V
START OPTIONS
END OPTIONS
SETUP
WELD MODE
UltimArc™ Control
Less
D
eposition
More
Deposition
Shorter
Arc
Longer
Arc
+
+
AMPS
WFS
VOLTS
TRIM
220
1.06
STEEL .035"
12
EFFECT / RANGE
-10.0 (SOFT to
ARC FOCUS
10.0 (STIFF)
DESCRIPTION
Arc Focus adjusts the arc from
a wide, soft arc good for out of
position work to a narrow, stiff
arc preferred for faster travel
speeds. The pulse frequency is
lower with a soft arc and higher
with a stiff arc.
EFFECT
Postflow Time
RUN-INWFS:
.
Start Procedure
DESCRIPTION
Adjusts the time that shielding
gas
flows
after
the trigger
is
pulled
and
p
rior to feeding wire.
Run-in sets the wire feed
speed from the time the trigger
is pulled until an arc is estab-
lished.
The Start Procedure controls
the WFS, Trim at a specified
time at the beginning of the
weld. During the start time, the
machine will ramp up or down
from the Start Procedure to the
preset Welding Procedure.
EFFECT
FUNCTION
ELECTRODE AND
Steel(Crisp)
Steel(Soft)
Stainless
Stainless
Stainless
GAS
2
CO
2
CO
2
Ar(Mix)
Ar(Mix)
Ar/He/CO
Ar/
Ar/
WIRE SIZE
0.030 0.035 0.045 0.052
---
14 19 28
95 12 22 201
66 36 46 ---
62 32 42 ---
--- 34 44 ---
START OPTIONS
END OPTIONS
WELD MODE
UltimArc™ Control
Pulse Crisp ArMix
Spot Timer
Adjust the time welding will
continue even if the trigger
is still pulled. This option
has no effect in 4-Step
Trigger Mode.
Crater Procedure
Crater Procedure controls the
WFS and Volts for a specified
time at the end of the weld
after the trigger is released.
During the Crater time, the
machine will ramp up or down
from the Weld Procedure to
the Crater Procedure.
Burnback:
The burnback time is the
amount of time that the weld
output continues after the wire
stops feeding. It prevents the
wire from sticking in the puddle
and prepares the end of the
wire for the next arc start.
Postflow Time
Adjusts the time that shielding
gas flows after the welding out-
put turns off.
START OPTIONS
END OPTIONS
SETUP
WELD MODE
UltimArc™ Control
Less
D
eposition
More
Deposition
Shorter
Arc
Longer
Arc
+
+
AMPS
WFS
VOLTS
TRIM
220
1.06
STEEL .035"
12
EFFECT / RANGE
-10.0 (SOFT to
ARC FOCUS
10.0 (STIFF)
DESCRIPTION
Arc Focus adjusts the arc from
a wide, soft arc good for out of
position work to a narrow, stiff
arc preferred for faster travel
speeds. The pulse frequency is
lower with a soft arc and higher
with a stiff arc.
EFFECT
Postflow Time
RUN-IN WFS:
.
Start Procedure
DESCRIPTION
Adjusts the time that shielding
gas
flows
after
the trigger
is
pulled
and
p
rior to feeding wire.
Run-in sets the wire feed
speed from the time the trigger
is pulled until an arc is estab-
lished.
The Start Procedure controls
the WFS, Trim at a specified
time at the beginning of the
weld. During the start time, the
machine will ramp up or down
from the Start Procedure to the
preset Welding Procedure.
EFFECT
FUNCTION
ELECTRODE AND
Steel(Crisp)
Steel(Soft)
Stainless
Stainless
Stainless
GAS
2
CO
2
CO
2
Ar(Mix)
Ar(Mix)
Ar/He/CO
Ar/
Ar/
WIRE SIZE
0.030 0.035 0.045 0.052
---
14 19 28
95 12 22 201
66 36 46 ---
62 32 42 ---
--- 34 44 ---
START OPTIONS
END OPTIONS
WELD MODE
UltimArc™ Control
Pulse Crisp ArMix
Spot Timer
Adjust the time welding will
continue even if the trigger
is still pulled. This option
has no effect in 4-Step
Trigger Mode.
Crater Procedure
Crater Procedure controls the
WFS and Volts for a specified
time at the end of the weld
after the trigger is released.
During the Crater time, the
machine will ramp up or down
from the Weld Procedure to
the Crater Procedure.
Burnback:
The burnback time is the
amount of time that the weld
output continues after the wire
stops feeding. It prevents the
wire from sticking in the puddle
and prepares the end of the
wire for the next arc start.
Postflow Time
Adjusts the time that shielding
gas flows after the welding out-
put turns off.
.$*+ -/$*)
*)/-*'*+/$*).