Sparky Group GUR 12S Drill User Manual


 
GUR 12SEN
8
BRUSH REPLACEMENT
&RPSOHWHO\XQVFUHZWKHFDSFig. 6, A
1H[WSXOOWKHEUXVKRXWIURPWKHEUXVKKROGHU
3. Worn brushes should be replaced in the same
KROGHUDQGSRVLWLRQDVUHPRYHG
4. Re-fasten the c ap.
&KHFNWKDWWKHWRROFDQRSHUDWH%HIRUHXVH
allowittorunforafewminutestoenablethe
brushes to settle.
Figure 6
Ⱥ
OPERATING THE WRENCH
1. Resting the unit after continuous operation.
$IWHU FRQWLQXRXV RSHUDWLRQ OHDYH WKH SRZHU
tool for 15 minutes or so to rest when replac-
ing the battery. The temperature of the motor,
switch, etc., will rise if operation is started again
LPPHGLDWHO\DIWHUEDWWHU\UHSODFHPHQWHYHQWX-
ally resulting in burnout.
3ODFHWKHSRLQWRIWKHGULYHUELWLQWKHVFUHZ
head.Keepthetoolpointedstraightatthe
screw.
$SSO\IRUZDUGSUHVVXUHWRWKHWRROWRSUHYHQWWKH
bit from slipping off the screw.
4. Turn the power tool on to start operation.
Alwayschecktorquewithatorquewrench,as
thefasteningtorqueisaffectedbymanyfactors
LQFOXGLQJWKHIROORZLQJ
9ROWDJH
/RZYROWDJHGXHWRDQHDUO\
discharged battery, will re-
duce the fastening torque.
%LWRUVRFNHW
VL]H
)DLOXUHWRXVHWKHFRUUHFWELW
RUVRFNHWVL]HZLOOFDXVHD
reductioninfasteningtorque.
Variable speed
WULJJHUVZLWFK
Operating the tool at a
reduced speed will decrease
the fastening torque.
%ROWVL]H
/DUJHUEROWGLDPHWHUVJHQHU
-
ally require higher fastening
WRUTXH)DVWHQLQJWRUTXHZLOO
DOVRYDU\DFFRUGLQJWROHQJWK
JUDGHDQGWRUTXHFRHI¿FLHQW
0DWHULDO
The type of material and sur-
IDFH¿QLVKRIWKHPDWHULDOZLOO
affect fastening torque.
)DVWHQLQJWLPH
/RQJHUIDVWHQLQJWLPHUHVXOWV
in increased fastening torque.
Using a longer fastening
time than recommended
couldcausethescrewsto
EHRYHUVWUHVVHGVWULSSHGRU
damaged.
5HIHUHQFH YDOXHV IRU WKH SURSHU IDVWHQLQJ WRUTXH
based on a standard bolt and resist high tension bolt
DUHSURYLGHGKHUH
Fig. 7 & 8
Figure 7
Figure 8
CAUTION: Metalcasecangethotduring
continuous operation.
1. Cautions on use of the speed control switch.
This switch has a built-in electronic circuit that
FDQYDU\WKHURWDWLRQVSHHG&RQVHTXHQWO\
when the switch trigger is pressed only slightly
ORZVSHHGURWDWLRQDQGWKHPRWRULVVWRSSHG
ZKLOHFRQWLQXRXVO\GULYLQJLQVFUHZVWKHFRP-
SRQHQWVRIWKHHOHFWURQLFFLUFXLWSDUWVPD\RYHU-
heat and be damaged.
pages-GUR 12S.indd 8 17.3.2006 . 09:59:25