Wagner SprayTech 2309 518 Paint Sprayer User Manual


  Open as PDF
of 32
 
45
Plast Coat 430
GB
AUTOMATIC SPRAY LANCE PNEUMATIC SPRAY LANCE
6.7
PREPARING THE MORTAR SPRAYING MACHINE
FIG. 15
Recommended sliding means for the mortar hose
Water is not sucient as a sliding means.
Danger of clogging!
Use cellulose paste (e.g. Metylan wallpaper
paste, art no. 2312136)
• Fill2–3lcellulosepasteintoasuitablecontainer.
• Connectthemortarsprayingmachinetothemainssupply.
The operation light (1) shows operational readiness.
• Placecontainerundermortarsprayingmachine.
• Pullsafetypin(2)totherearandpressdownmortarspray-
ing machine frame (3) until machine engages in the bottom
position.
Risk of injury from escaping material.
Before switching on, always check that the
material tap on the spray lance is closed.
Close material tap whenever stopping
work.
• Setselectorswitch(4)to“A”.
• Setdeliveryvolumecontroller(5)to„3“.
Do not bend the mortar hose!
Protect it against damage, for exam-
ple against being driven over as well as
against sharp objects and edges.
• Holdthespraylanceoverthecontainer.
• Openmaterialtap(3,Fig.16)onspraylance(materialtap
facingtotherear),themortarsprayingmachineisswitched
on.
• Ifcellulosepasteispumpedintothemortarhose,closema-
terialtap(3,Fig.16).(Materialtapat90°tospraylance)
• Replacecontainerandlubricantwithcontainerandcoating
material.
• Holdspraylanceabovecontainerwithcellulosepaste.
• Openmaterialtap(3,Fig.16)onspraylance.
• As soon as coating material exits from spray lance,
close material tap (3, Fig. 16).
Themortarsprayingmachineisnowfullandready.
6.7 PREPARING THE MORTAR SPRAYING MACHINE
FIG. 15
Recommended sliding means for the mortar hose
Water is not sucient as a sliding means.
Danger of clogging!
Use cellulose paste (e.g. Metylan wallpaper
paste, art no. 2312136)
• Fill2–3lcellulosepasteintoasuitablecontainer.
• Connectthemortarsprayingmachinetothemainssupply.
The operation light (1) shows operational readiness.
• Placecontainerundermortarsprayingmachine.
• Pullsafetypin(2)totherearandpressdownmortarspray-
ing machine frame (3) until machine engages in the bottom
position.
Risk of injury from escaping material.
Before switching on, always check that the
material tap on the spray lance is closed.
Close material tap whenever stopping
work.
• Setselectorswitch(4)to“A”.
• Setdeliveryvolumecontroller(5)to„3“.
• Switchocompressor.
Do not bend the mortar hose!
Protect it against damage, for exam-
ple against being driven over as well as
against sharp objects and edges.
• Holdthespraylanceoverthecontainer.
• Set selector switch to “F”.
• Openmaterialtap(1,Fig.17)onspraylance.(Materialtapat
90°tospraylance)
• Ifcellulosepasteispumpedintothemortarhose,closema-
terial tap (material tap facing to the rear).
• Setselectorswitchto“A”.
• Replacecontainerandlubricantwithcontainerandcoating
material.
• Holdspraylanceabovecontainerwithcellulosepaste.
• Set selector switch to “F”.
• Openmaterialtap(1,Fig.17)onspraylance.
• Assoonascoatingmaterialexitsfromspraylance,closema-
terial tap (1, Fig. 17).
• Setselectorswitchto“A”.
• Switchoncompressor.
Themortarsprayingmachineisnowfullandready.
commIssIonIng
 previous next