Filter
Top Products
51
• Push the SPEED CONTROL
LEVER (1O) forward for FORWARD
saw movement, or to the rear for
REVERSE saw movement. The
further you push the lever the faster
the speed.
DO NOT OPEN the TRANSMISSION BYPASS
VALVE (6J) to neutral while the saw is parked
on a grade (or hill), The Operator will lose
control and injury or damage could occur.
Rear Pivot Model (with Differential System–
If equipped)
Moving The Saw With The Engine Off:
• Turn ENGINE START SWITCH (1H) to the “1”
(RUN) position.
• Raise the saw by pressing up on the TOGGLE SWITCH
(1P) on the SPEED CONTROL LEVER (1O) until
the DIAMOND BLADE (2E) (if installed) clears the
pavement surface.
• Turn ENGINE START SWITCH (1H) to the “0”
(STOP) position.
• Put the SPEED CONTROL LEVER (1O) into the STOP
POSITION (1BB).
• Press and hold the Differential Switch (1J) to
the Right.
• Hold one Handle Bar (1B), and Press and hold the
Differential Switch (1J) to the Right. The saw can now
be moved by standing behind it and pushing. If the
Differential Switch (1J) is released, the saw can not be
moved with the engine off.
DO NOT attempt to push the saw while it is
in NEUTRAL on a grade (or hill). The saw
operator could lose control of the saw and
cause injury to himself or other persons in
the area.
Moving The Saw With Engine On:
• Raise the saw by pressing up on the TOGGLE
SWITCH (1P) on SPEED CONTROL LEVER (1O)
until DIAMOND BLADE (2E) (if installed) clears the
pavement surface.
• Set the WATER SAFETY SWITCH (1L) button to the
“0” (OFF) position.
• SPEED CONTROL LEVER (1O) must be in the STOP
POSITION (1BB) to start the saw. The engine WILL
NOT start unless the SPEED CONTROL LEVER (1O)
is in the STOP (1BB) position.
• Turn the ENGINE THROTTLE (1F) to a low
speed setting.
• Set the BLADE CLUTCH SWITCH (1V) (if equipped)
to “0” (OFF).
* In cold conditions (below 32° F (0° C)) push in on the
ENGINE START SWITCH (1H) for 15 seconds. This
preheats the engine for cold weather starting.
• Turn the ENGINE START SWITCH (1H) to the “2”
(START) position until the engine starts, then release
the switch. It will return to RUN position. If the engine
does not start, repeat these steps.
3 Transport (Blade Removed)
(See Figures 1, 2, and 5)
Turn engine off. Set SPEED CONTROL LEVER
(1O) to STOP POSITION (1BB). Remove
DIAMOND BLADE (2E) before transport.
When moving the saw up and down ramps, with engine
on, use extreme caution.
• To go DOWN a ramp drive the saw FORWARD slowly.
• To go UP a ramp, back the saw in REVERSE slowly.
Rear Pivot Model: Machine must have DIFFERENTIAL
SWITCH (1J) in the center “Lock” position if moving
saw up or down ramps! DO NOT shift DIFFERENTIAL
SWITCH (1J) to the Left “Pivot” position if moving the
saw up or down ramps!
For steep ramps, always use a winch. Never
stand below the machine.
Lifting the Saw: The saw can only be lifted by the factory
installed Lifting Bail (6A).
To Transport By Vehicle:
• Set ENGINE START SWITCH (1H) in the OFF position.
• Set SPEED CONTROL LEVER (1O) in the STOP
POSITION (1BB).
• Push Handle Bars (1B) inward and tighten Knobs (1A).
Block the saw in place or secure it into
place using the factory installed TIE DOWN
LUGS (3-1H, 3-2H), front and rear to prevent
movement during transport.
4 Check Before Starting
Take into account the working conditions
from health and safety point of view.
• Fuel (Check the engine maintenance manual.) Use No.
2 Diesel Fuel for normal conditions. Fill tank at FUEL
TANK FILL (5E) location.
• Check that the engine oil level is correct. Because the
engine often operates at an angle, check the oil level
(with engine horizontal) frequently to ensure that the oil
level never falls below the lower mark on the ENGINE
OIL DIPSTICK (5B). SAE 15W40 CF, CF-4, CG-4, or
CI-4 engine oil is recommended.
• For start up, refer to the Yanmar engine manual.
• Push the SPEED CONTROL LEVER
(1O) forward for FORWARD saw
movement, or to rear for REVERSE
saw movement. The further you push
the lever the faster the speed.