Filter
Top Products
RULES FOR SAFE OPERATION (Continued)
USE THE PROPER EXTENSION CORD. Make
sure yourextensioncordis in goodcondition.
When usingan extensioncord, be sureto use
one heavyenough to carrythe currentyour
productwill draw. An undersizedcord willcause
a drop in linevoltage resultingin lossof power
and overheating.A wire gage size (A,W.G.) of at
least14 is recommendedfor an extensioncord
25 feet or less in length. If in doubt,use the next
heaviergage. The smaller the gage number,the
heavierthe cord.
INSPECT EXTENSION CORDS PERIODI-
CALLY and replace ifdamaged.
DRESS PROPERLY. Do notwear loose clothing,
gloves, neckties,dngs, bracelets,or other
jewelry. They can get caught and drew you into
movingparts. Rubbergloves and nonsliptoot-
wear are recommendedwhenworkingoutdoors.
Ais0 wear protectivehaircovedngto contain long
hair.
ALWAYS WEAR SAFETY GLASSES WITH
SIDE SHIELDS. Everydayeyeglasses haveonly
impact-resistantlenses;they are NOT safety
glasses.
PROTECT YOUR LUNGS. Wear a face or dust
maskif the cuttingoparetlon isdusty,
PROTECT YOUR HEARING. Wear headng
protectiondudngextended padods of oparetion.
SECURE WORK. Use clamps ora viseto hold
workwhen practical.I_ssafer than usingyour
hand and Itfrees both handsto operete tool.
DO NOT OVERREACH. Keep properfooting and
balanceat all times.
MAINTAIN TOOLS WITH CARE. Keeptools
sharpand clean for borer and safer pedor-
manca. Followinstructionsfor lubricatingand
changingaccassodes.
DISCONNECT ALL TOOLS. When not inuse,
before servicing,or when changingattachments,
blades, bits,cutters, etc., all toolsshouldbe
disconnected.
AVOID ACCIDENTAL STARTING. Be sure
switchis offwhen pluggingin.
USE RECOMMENDED ACCESSORIES. The
use of improperaccessoriesmay cause dsk of
injury.
NEVER STAND ON TOOL. Sedous injurycould
occurif the tool istippedor ifthe blade is unln.-
tanUonailycontacted.
CHECK DAMAGED PARTS. Beforefurtheruse
ofthe tool, a guard or other part that is damaged
shouldbe carefullychecked todetermine that it
willoperate properlyand performits intended
M
M
function. Check for alignmentof movingpads,
bindingof movingpart==,breakage ofparts,
mountingand any otherconditions that may
affect its operation.A guard or otherpart thatis
damaged mustbe propady repairedor replaced
by a qualifiedservice technicianat a Sears store
to avoiddsk of personalinjury.
NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN THE POWER OFF. Do not
leavetool untilit comes to a complete stop.
RRMLY CLAMP OR BOLT your miter sew to a
workbenchor table at approximatelyhipheight.
USE ONLY CORRECT BLADES. Do not use
blades with incorrectsize holes;Never use blade
washersor bladebolts that are defec_veor
incorrect.The maximumblade capacity of your
saw is 10 in.
KEEP BLADES CLEAN, SHARP AND WITH
SUFFICIENT SET. Sharpblades minimize
stallingand kickback.
DO NOT REMOVE THE SAW'S BLADE
I
GUARDS. Never operatethe sew with any guard
or coverremoved. Make sure all guardsare
operatingpropadybefore each use.
KEEP HANDS AWAY FROM CUTTING AREA.
Keep handsaway fromblades. Do not reach
underneathwork or aroundor underthe blade
while bladeis rotating. Do notattempt to remove
cut matedal when blade ismoving.
_1= WARNING: Bladecoastsafter turnoff.
M
M
M
DO NOT ABUSE CORD. Never yankcord to
disconnectitfrom receptacle. Keep cordfrom
heat, oil, and sharp edges.
INSPECT TOOL CORDS PERIODICALLY and if
damaged, have repairedby a qualifiedservice
technicianat a Sears store. Stay constantly
aware of cordlocationand keep it well away
from the rotatingblade.
USE OUTDOOR EXTENSION CORDS. When
toolis used outdoors,use onlyextensioncords
with approvedgroundconnection that are
intendedfor useoutdoorsand somarked.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defectiveswitches
replacedby a qualifiedservicetechnicianat a
Sears store.
KEEP TOOL DRY, CLEAN, AND FREE FROM
OIL AND GREASE. Alwaysuse a clean cloth
when cleaning. Never use brake fluids, gasoline,
petrolaum-basedproducts,or any solventsto
clean tool.
4