2 General Specifications
MITSUBISHI CNC
30
(4) Machine output (CG32)
Digital output 32 points (1st station)
(5) Machine output (CG34)
Digital output 32 points (2nd station)
(Note) This is not available for FCU7-DX621.
(6) Machine output (CG36)
FCU7-DX731: Digital output 32 points (3rd station)
FCU7-DX621/DX721: Digital output 16 points (3rd station) (with analog output)
(Note) This is not available for FCU7-DX711.
<Cable side connector type>
Connector: 7940-6500SC
Strain relief: 3448-7940
Recommended manufacturer: 3M
(Note 1) FCU7-DX621/DX721 uses 16 points of digital outputs, Y240 to Y24F.
(Note 2) COM (3A, 3B, 4A, and 4B) is connected to 24VDC inside the unit.
Each station has fixed input/output assignments. Refer to "PLC Interface Manual" for details.
CG32 CG34 CG36 (Note 1)
BA BA BA
20 O Y200 20 O Y210 20 O Y220 20 O Y230 20 O Y240 20 O Y250
19 O Y201 19 O Y211 19 O Y221 19 O Y231 19 O Y241 19 O Y251
18 O Y202 18 O Y212 18 O Y222 18 O Y232 18 O Y242 18 O Y252
17 O Y203 17 O Y213 17 O Y223 17 O Y233 17 O Y243 17 O Y253
16 O Y204 16 O Y214 16 O Y224 16 O Y234 16 O Y244 16 O Y254
15 O Y205 15 O Y215 15 O Y225 15 O Y235 15 O Y245 15 O Y255
14 O Y206 14 O Y216 14 O Y226 14 O Y236 14 O Y246 14 O Y256
13 O Y207 13 O Y217 13 O Y227 13 O Y237 13 O Y247 13 O Y257
12 O Y208 12 O Y218 12 O
Y228 12 O Y238 12 O Y248 12 O Y258
11 O Y209 11 O Y219 11 O Y229 11 O Y239 11 O Y249 11 O Y259
10 O Y20A 10 O Y21A 10 O Y22A 10 O Y23A 10 O Y24A 10 O Y25A
9 O Y20B 9 O Y21B 9 O Y22B 9 O Y23B 9 O Y24B 9 O Y25B
8 O Y20C 8 O Y21C 8 O Y22C 8 O Y23C 8 O Y24C 8 O Y25C
7 O Y20D 7 O Y21D 7 O Y22D 7 O Y23D 7 O Y24D 7 O Y25D
6 O Y20E 6 O Y21E 6 O Y22E 6 O Y23E 6 O Y24E 6 O Y25E
5 O Y20F 5 O Y21F 5 O Y22F 5 O Y23F 5 O Y24F 5 O Y25F
4
COM
(Note 2)
4
COM
(Note 2)
4
COM
(Note 2)
4
COM
(
Note 2)
4
COM
(Note 2)
4
COM
(Note 2)
3
COM
(Note 2)
3
COM
(Note 2)
3
COM
(Note 2)
3
COM
(Note 2)
3
COM
(Note 2)
3
COM
(Note 2)
2 I 24VDC 2
GND
(0V)
2 I 24VDC 2
GND
(0V)
2 I24VDC 2
GND
(0V)
1 I 24VDC 1
GND
(0V)
1 I 24VDC 1
GND
(0V)
1 I24VDC 1
GND
(0V)
B1 B20
A1 A20