Filter
Top Products
3
GENERAL SAFETY RULES
READ ALL INSTRUCTIONS
n KNOW YOUR POWER TOOL. Safe operation of this
power tool requires that you read and understand this
operator’s manual and all labels affixed to the tool. Learn
its applications and limitations as well as the potential
hazards.
n GUARD AGAINST ELECTRICAL SHOCK by preventing
body contact with grounded surfaces such as pipes, ra-
diators, ranges, refrigerator enclosures.
n KEEP GUARDS IN PLACE and in good working order.
Never operate the tool with any guard or cover removed.
Make sure all guards are operating properly before each
use.
n REMOVE ADJUSTING KEYS AND WRENCHES. Get
in the habit - before turning on tool - that hex keys and
adjusting wrenches are removed from tool.
n KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools or
pieces of wood on the machine while it is in operation.
n DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools near gasoline or other flammable
liquids, in damp or wet locations, or expose them to rain.
Keep the work area well lighted.
n KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or extension
cord while operating.
n MAKE WORKSHOP CHILDPROOF with padlocks and
master switches or by removing starter keys.
n DO NOT FORCE THE TOOL it will do the job better and
safer at the rate for which it was designed.
n USE THE RIGHT TOOL FOR THE JOB. Do not force
the tool or attachment to do a job for which it was not
designed for. Use it only the way it was intended.
n USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. A wire
gage size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gage. The smaller the gage number, the
heavier the cord.
n DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry that could get
caught and draw you into moving parts. Non-slip foot-
wear is recommended. Wear protective covering over
long hair.
n ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact resis-
tant lenses; they are not safety glasses.
n PROTECT YOUR LUNGS. Wear a face or dust mask if
the operation is dusty.
n PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
n SECURE WORK. Use clamps or a vise to hold the work
when practical. It’s safer than using your hand and frees
both hands to operate the tool.
n DO NOT OVERREACH. Keep proper footing and balance
at all times.
n MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions
for lubricating and changing accessories.
n DISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, all tools should
be disconnected.
n AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
n USE RECOMMENDED ACCESSORIES. Consult this
operator’s manual for recommended accessories. The
use of improper accessories may cause risk of injury.
n NEVER STAND ON TOOL. Serious injury could occur if the
tool is tipped or if the bit is unintentionally contacted.
n CHECK DAMAGED PARTS. Before using the tool, a guard
or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting and
any other conditions that may affect operation. A guard
or other part that is damaged must be properly repaired
or replaced by an authorized service center to avoid risk
of personal injury.
n NEVER LEAVE TOOL RUNNING UNATTENDED, TURN
THE POWER OFF. Do not leave tool until it comes to a
complete stop.
n DO NOT ABUSE CORD. Never yank the cord to disconnect
it from the receptacle. Keep the cord from heat, oil, and
sharp edges.
n KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
n STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
n DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
n ALWAYS TURN SWITCH OFF before disconnecting it
to avoid accidental starting.
WARNING:
Read and understand all instructions. Failure
to follow all instructions listed below, may result
in electric shock, fire and/or serious personal
injury.