Filter
Top Products
Technical Data
313289S 85
Technical Data
* Minimum flow rate is dependent on material being sprayed and mixing capability. Test your material specific to
flow rate.
Mixed ratio range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1-10:1 (in 0.1 increments)
Ratio tolerance range (before alarm) . . . . . . . . . . . . . . . . +/- 5%
Flow rates
Minimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 qt./min. (0.95 liter/min.)*
3 gal./min/ (11.4 liter/min.)
Fluid viscosity range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-20,000 cps (heavier viscosities can be mixed using
heat, circulation, and/or pressure feeding)
Fluid filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mesh, (238 micron) standard on pump outlets (filter
assembly not included on some models)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npt(f)
Fluid inlets without feed kits . . . . . . . . . . . . . . . . . . . . . . . 1 1/4 npt(m)
Maximum fluid working pressure of mixed material
50:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5200 psi (35.8 MPa, 358 bar)
6300 psi (43.5 MPa, 435 bar)
Maximum fluid temperature . . . . . . . . . . . . . . . . . . . . . . . 160° F (71° C)
Air supply pressure range . . . . . . . . . . . . . . . . . . . . . . . . 50-150 psi (0.35-1.0 MPa, 3.5-10.3 bar)
Maximum pump air set pressure
50:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105 psi (0.74 MPa, 7.4 bar)
85 psi (0.60 MPa, 6.0 bar)
Maximum pump inlet fluid feed pressure . . . . . . . . . . . . . 250 psi (1.7 MPa, 17 bar)
Maximum air consumption at 100 psi (0.7 MPa, 7.0 bar)
in scfm (m
3
/min.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 scfm per gpm (1.96 m
3
/min. per lpm)
Ambient temperature range
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32-135° F (0-57° C)
30-160° F (-1-71° C)
Environmental conditions rating . . . . . . . . . . . . . . . . . . . . Indoor/outdoor use
Altitude up to 4000 m
Maximum relative humidity to 99% up to 130° F (54° C)
Pollution degree (11)
Installation category (2)
Sound pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 dBA at 100 psi (0.7 MPa, 7 bar)
Sound power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dBA at 100 psi (0.7 MPa, 7 bar)
Wetted parts
Suction tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flush pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hoses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pumps (A and B) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metering valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
aluminum
carbide, PTFE, stainless steel, UHMWPE
nylon
carbon steel, alloy steel, 303, 440, 17-ph grades stainless
steel, zinc and nickel plating, ductile iron, tungsten car-
bide, PTFE
carbon steel, nickel plating, carbide, polyethylene, leather
carbon steel, nickel plating, carbide, 302 stainless steel,
PTFE, UHMWPE
stainless steel housing with acetal elements
Refer to spray gun manual
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dimensions, page 82
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Base sprayer (XM1A00 and XM5A00 models)
742 lbs (336.87 kg)
(Add component weight(s) to base sprayer weight for your
specific model weight. See component manuals.)