Filter
Top Products
Model G0768/G0769 (Mfd. Since 8/15)
-21-
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Installed Components (Figure 10) Qty.
A. 3-Jaw Chuck 4" w/Internal Jaw Set ............ 1
B. Steady Rest ................................................ 1
C. 4-Way Tool Post ......................................... 1
D. Drill Chuck
1
⁄2" w/Chuck Key (G0769) ........ 1
E. Milling Headstock (G0769) ......................... 1
F. Backsplash ................................................. 1
G. Tailstock ...................................................... 1
H. Follow Rest (Not Shown) ............................ 1
V. Fuse Set ..................................................... 1
— 10A (G0768) ........................................... 1
— 15A (G0768) ........................................... 1
— 10A (G0769) ........................................... 2
— 15A (G0769) ........................................... 1
W. Dead Center MT#2 .................................... 1
X. Dead Center MT#3 ..................................... 1
Y. Change Gear Set ....................................... 1
— Change Gear (20-tooth, Installed) ......... 2
— Change Gear (30-tooth, Installed) ......... 2
— Change Gear (33-tooth) ......................... 1
— Change Gear (40-tooth) ......................... 1
— Change Gear (50-tooth) ......................... 1
— Change Gear (53-tooth) ......................... 1
— Change Gear (55-tooth) ......................... 1
— Change Gear (57-tooth) ......................... 1
— Change Gear (60-tooth) ......................... 1
— Change Gear (63-tooth) ......................... 1
— Change Gear (65-tooth) ......................... 1
— Change Gear (70-tooth) ......................... 1
— Change Gear (71-tooth) ......................... 1
— Change Gear (72-tooth) ......................... 1
— Change Gear (80-tooth, Installed) ......... 2
— Change Gear (84-tooth, Installed) ......... 1
Z. 4-Jaw Universal Chuck 4" (Not Shown) ..... 1
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Loose Components (Figure 11) Qty.
I. Chip Pan (Not Shown) ................................ 1
J. Toolbox ....................................................... 1
K. Oil Bottle for Oil .......................................... 1
L. Faceplate 6
3
⁄4" ........................................... 1
M. 3-Jaw Chuck External Jaw Set .................. 1
N. Hex Wrench Set (2.5, 3, 4, 5, 6mm) ......1 Ea
O. Flat Head Screwdriver #2 ........................... 1
P. Phillips Head Screwdriver #2 ..................... 1
Q. Spanner Wrench ........................................ 1
R. Wrench Set (6/7, 8/10, 14/16mm) ............... 1
S. Lathe Chuck Key ........................................ 1
T. Square Socket T-Wrench ........................... 1
U. Handwheel Handles ................................... 2
Figure 10. Installed components (G0769 shown).
A
B
C
F
G
D
E
Figure 11. Packaged components.
S
U
L
M
N
O
P
Q
R
T
U
V
W
X
Y
J
K
S