Filter
Top Products
HIGH
PRESSURE SPRAY CAN CAUSE EXTREMELY SERIOUS INJURY.
FOR
PROFESSIONAL
USE
ONLY.
OBSERVE
ALL
WARNINGS.
Read
and
understand
all
instruction
manuals,
tags,
and
warnings
before
operating
equipment.
FLUID INJECTION
HAZARD
General Safety
This equipment generates very high fluid pressure. Spray from
the gun, leaks or ruptured components can inject fluid
through your skin and into your body and cause extremely
serious bodily injury, including the need for amputation. Also,
fluid injected or splashed into the eyes or onto the skin can
cause serious damage.
NEVER point the spray gun at anyone or any part of the body.
NEVER put hand or fingers over the spray tip. NEVER try to
“blow back” paint; this is NOT an air spray system.
spraying.
ALWAYS have the
tip
guard in place on the spray gun when
ALWAYS follow the Pressure Relief Procedure. below.
before cleaning or removing the spray tip or servicing any
system equipment.
~.
~~ ~
NEVER try to.stop or deflect leaks
with
your hand or body.
before each use.
Be sure equipment safety devices are operating properly
Medical Alert
-
Airless
Spray
Wounds
If any fluid appears to penetrate your skin, get
EMERGENCY
MEDICAL CARE AT ONCE.
DO
NOT TREAT AS A
SIMPLE CUT.
Tell the doctor exactly what fluid was injected.
jury.
It
Is
important
to
treat the
injury surgically as
soon
Note
to
Physician: injection
in
the skin is a traumatic
in-
as possible.
Do
not delay treatment to research toxiciry.
Toxicity
is
a
concern
with
some exotic coatings injected
directly into the blood stream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable.
Spray Gun Safety
Devices
Be sure
all
gun safety devices are operating properly before
each use. Do not remove or
modify
any part of the gun; this
can cause
a
malfunction and result
in
serious bodily injury.
Whenever you stop spraying, even for a moment, always set
Safety
Latch
the gun safety latch in the closed or “safe” position, making
the gun inoperative. Failure to set the safety latch can result
in
accidental triggering of the gun.
The gun diffuser breaks up spray and reduces the risk of fluid
Diffuser
injection when the tip is not installed. Check diffuser operation
regularly. Follow the Pressure Relief Procedure, below,
then remove the spray tip. Aim the gun into
a
metal
pail,
holding the gun firmly to the pail. Using the lowest possible
to an irregular stream, replace
the diffuser immediately.
pressure, trigger the gun. If the fluid emitted is not diffused
in-
Tip
Guard
ALWAYS have the tip guard in place on the spray gun while
spraying. The tip guard alerts you to the fluid injection hazard
and helps reduce, but does not prevent, the risk of accidental
-
ly placing your fingers or any part of your body close to the
spray tip.
Spray
Tip
Safety
the spray tip clogs while spraying, engage the gun safety latch
Use extreme caution when cleaning or changing spray tips.
If
immediately. ALWAYS follow the Pressure Relief Pro
-
cedure and then remove the spray tip to clean
it.
fully relieved
and the gun safety
latch is engaged.
NEVER wipe
off
build
-
up around the spray tip
until
pressure is
Pressure
Relief
Procedure
To reduce the risk of serious bodily injury, including fluid injection, injury from splashing fluid or solvent
in
the eyes or on the
skin, moving parts or electric shock, always follow this procedure whenever you shut
off
the sprayer, when checking or servic
-
ing any part of the spray system, when installing, cleaning or changing spray tips, and whenever you stop spraying.
(1
1
Engage
the gun safety latch.
(21
Turn the ON/OFF switch to OFF.
(31
Unplug the power supply cord.
(4)
Disengage the gun safety latch.
gun safety latch.
17)
Open the drain valve, having a container ready to catch the drainage.
181
Leave the drain valve open until
(51
Hold a metal pan
of
the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.
(61
Engage the
you are ready to spray again.
steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then
loosen
If
you
suspect that the spray
tip
or hose
is
completely clogged, or that pressure has not been
fully
relieved after following the
completely. Now clear the
tip
or hose.
I
~~
ENGAGE SAFETY
TURN
SWITCH
TO OFF
IATCH
UNPLUG
CORD
DISENGAGE SAFETX
ANDTRIGGERQUN:
ENGAGE SAFETY AGAIN
OPEN DRAIN VALVE
I
2
307-671