Mitsumi electronic 55K Welding System User Manual


 
PARAMETERS
65
4.1.2 List of Parameters Classified by Purposes of Use
Set the parameters according to the operating conditions. The following list indicates purposes of use and
parameters.
Parameter Numbers
Purpose of Use
Parameter numbers which must be set
Switch-over to optimum excitation control operation Pr. 14, Pr. 60
Adjustment of acceleration/deceleration time and
pattern
Pr. 7, Pr. 8, Pr. 20, Pr. 21, Pr. 160
Selection of optimum output characteristic for load
characteristic
Pr. 3, Pr. 14, Pr. 19, Pr. 60
Limit of output frequency Pr. 1, Pr. 2
Operation over 60Hz Pr. 903, Pr. 905
Adjustment of frequency setting signal and output Pr. 73, Pr. 74, Pr. 902 to Pr. 905
Adjustment of motor output torque Pr. 0
Adjustment of brake operation Pr. 10, Pr. 11, Pr. 12
Multi-speed operation
Pr. 1, Pr. 2, Pr. 4, Pr. 5, Pr. 6, Pr. 15, Pr. 24, Pr. 25, Pr. 26, Pr. 27,
Pr. 160
Jog operation Pr. 15, Pr. 16
Frequency jump operation Pr. 31, Pr. 32, Pr. 33, Pr. 34, Pr. 35, Pr. 36
Automatic restart after instantaneous power failure Pr. 57, Pr. 58
Related to operation
Optimum acceleration/deceleration within continuous
rating range
Pr. 60
To perform commercial power supply
inverter
switch-over operation
Pr. 135 to Pr. 139, Pr. 160, Pr. 180 to Pr. 186,
Pr. 190 to Pr. 195
Timing of magnetic brake operation Pr. 42, Pr. 160, Pr. 190 to Pr. 195
Reversible operation according to analog signal
polarity
Pr. 28, Pr. 73
Sub-motor operation Pr. 0, Pr. 3, Pr. 7, Pr. 8, Pr. 44, Pr. 45, Pr. 46, Pr. 47
To make desired output characteristics Pr. 100 to Pr. 109
Operation via communication with personal computer Pr. 117 to Pr. 124, Pr. 160
Operation under PID control
Pr. 73, Pr. 79, Pr. 128 to Pr. 134, Pr. 160,
Pr. 180 to Pr. 186, Pr. 190 to Pr. 195
Advanced PID control
(NA, EC versions only)
Pr. 128, Pr. 130 to Pr. 134, Pr. 180 to Pr. 186, Pr. 190 to Pr. 195,
(Pr. 320 to Pr. 322), Pr. 500 to Pr. 516
To make backlash compensation Pr. 140 to Pr. 143
Related to application operation
To suppress noise Pr. 72, Pr. 240
Calibration of frequency meter Pr. 54, Pr. 55, Pr. 56, Pr. 158, Pr. 160, Pr. 900, Pr. 901
Adjustment of digital frequency meter Pr. 54, Pr. 55, Pr. 56, Pr. 900
Display of speed, etc. Pr. 37, Pr. 52, Pr. 53, Pr. 160
Clearing of inverter's actual operation time Pr. 171
Related to
monitoring
Alarm code output selection Pr. 76
Function rewrite prevention Pr. 77
Reverse rotation prevention Pr. 78
To group parameters Pr. 160, Pr. 173 to Pr. 176
Related to
incorrect
operation
prevention
To set initial values for parameters Pr. 199
Assignment of input terminal functions Pr. 180 to Pr. 186
Assignment of output terminal functions Pr. 190 to Pr. 195
To increase cooling fan life Pr. 244
Motor overheat protection Pr. 9, Pr. 71
Automatic restart after alarm stop Pr. 65, Pr. 67, Pr. 68, Pr. 69
Selection of key beep Pr. 990
Others
Inverter reset selection Pr. 75
4