Filter
Top Products
9
ENGLISH
Modification of the machine and use
of non-OEM parts or parts not tested
nor approved by the manufacturer
Defects and malfunctions
Noise
Contamination upon contact
Grounding and insulation
3.3Specific Safety Instruc-
tions
Lack of experience and expertise with
compound miter saws
Personal injury inflicted by track arm
holder and sawhead assembly
x Minimize the amount of woo d dust
escaping from the machine and the
job site:
Remove dust deposits from the
work area. DO NOT BLOW THE
DUST AWAY WITH COM-
PRESSED AIR BECAUSE THIS
WILL ONLY SPREAD THE
DUST RATHER THAN REMOV-
ING IT.
Make sure the dust collector is
leak free and repair any leaks
immediately.
Keep your work area well venti-
lated at all times.
A DANGER
x Unauthorized changes and/or mod-
ifications affect machine safety and
are not allowed. The manufacturer
disclaims any liability for any dam-
age or injuries resulting from
changes or modifications or from
the use of non-OEM parts. The use
of any parts
not supplied or
approved by the manufacturer
voids the warranty of the machine.
A WARNING
x Follow all instructions given in this
manual strictly when you assem-
ble and start up the machine.
A DANGER
x Keep the machine and all accesso-
ries in good, clean and safe work-
ing condition. Strictly observe all
maintenance instructions contained
in this manual.
x Before every use of this machine
check for possible damage. Every
time you want to
use the machine
make sure that all safety devices
and protective guards are undam-
aged and fully operational.
x Check that all moving parts operate
smoothly and without jamming.
x Make sure that all parts and acces-
sories
are properly installed and
safely secured to ensure the safe
and trouble-free operation of the
machine.
A WARNING
x Any damaged parts or protection
devices must be replaced by fully
qualified and factory authorized
personnel only.
x Damaged switches may only be
replaced at a factory authorized
service center. For information on
the service center nearest you
,
refer to the information contained in
"Warranty Terms and Conditions"
at the beginning of this manual.
x NEVER OPERATE THE MACHINE
IF THE ON/OFF SWITCH IS DAM-
AGED!
x If the machine is not working prop-
erly, mark or tag it accordingly and
th
en move it to a safe place where
it cannot be used inadvertently, or
by unauthorized persons or any
children.
A WARNING
x Prevent hearing loss! Use ear pro-
tection. Always wear ANSI
approved ear protection such as
ear plugs or ear muffs.
A WARNING
x The insulation of power cords may
contain substances that are known
or suspected to cause cancer,
damage to reproductive organs
and/or the ability to procreate, and/
or may cause damage to fetuses
and unborn children.
Wash your hands
thoroughly with
soap and water every time after
touching the power cord.
A DANGER
x Fully insulated machines have a
special plug. Consult an electrician
if you do not have a matching out-
let.
x Do not tamper with the plug or the
outlet yourself. Consult a qualified
electrician for assistance.
A DANGER
A DANGER
x When using this machine, observe
the following safety instructions to
avoid the risk of personal injury or
property damage.
A WARNING
x PAY ATTENTION TO AND FOL-
LOW, WHERE APPLICABLE, ALL
SAFETY RULES AND REGULA-
TIONS, REGULATIONS FOR
ACCIDENT PREVENTION,
OCCUPATIONAL SAFETY AND
HEALTH ADMINISTRATION
(OSHA) RULES AND REGULA-
TIONS, ENVIRONMENTAL AND
ALL OTHER FEDERAL, STATE
AND LOCAL LAWS IN EFFECT
AT THE OPERATI
ON SITE, AS
THEY APPLY TO MITER SAWS.
x This machine shall only be oper-
ated by persons familiar with miter
saws, their operation and the spe-
cific risks associated with the oper-
ation of miter saws.
x Contact your supervisor,
instructor
or any other qualified individual in
case you lack substantial experi-
ence and expertise regarding the
operation of miter saws.
A WARNING
x Hold the handle firmly when you
start the cutting operation. The risk
of the sawhead being kicked up is
particularly high at the moment
when the saw blade makes its first
contact with the work piece.
x If you tilt th
e sawhead assembly to
the side, hold it at the handle and
keep your fingers away from the
track arm holder and out of its tilt-
ing range.
x Avoid lateral pressure on the saw-
head when making grooves. Use
clamps to firmly position your work
piece and secure it against acci-
dental movement.