Filter
Top Products
39
206-4271
Installer Menu (Cont.)
000 - INSTALLER SEQUENCE
Species entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Energy saving feature. Determines the number of hours, in the
range 1 to 7, of inactivity allowed, either at the TV control panel
or from the remote, before the TV automatically turns itself OFF. If
set to 0, Power Management is disabled.
002 - AC ON (AC Power Switchable)
If set to 1, this allows the TV to turn ON when AC power is
applied. Pressing the POWER button is not necessary. This is
desirable if the TV is plugged into a switched AC outlet (i.e., a
set-top box). Set to 2 or 3 to enable the Instant ON feature (see
additional information below). Set to 0 (default) for standard TV
turn ON/OFF operation.
The Instant ON feature allows the TV to turn ON when AC power
is applied, but with video and audio muted (Muted ON). The TV
retains its ON status while appearing to be OFF. Pressing the
POWER button toggles Off/On the video and audio mutes, so that
the TV appears to turn ON instantly.
• If this item is set to 2, the TV will reboot to check for and down-
load updates from the Pro:Centric server at every turn OFF. This
setting is not recommended if the TV will be congured with a
resident application.
• If this item is set to 3, the TV will not reboot to check for and
download updates at turn OFF. This setting is recommended if
the TV will be congured with a resident application. In this mode,
the check for and download of updates is under application
control. Refer to your site-specic documentation for further
information on conguring the TV with a resident application.
When this item is set to 2 or 3, the TV will reboot once every 24
hours and, if applicable (i.e., item 119 DATA CHANNEL is set),
check for and download updates from the Pro:Centric server. The
time at which this event occurs depends on the setting of item 121
UPDATE TIME HR. See item 121 description for further informa-
tion. Once the update cycle is complete, the TV completes the
reboot and resumes its Muted ON state.
Note: If set to 1, the TV does not respond to ON/OFF commands
from either the remote or the display panel, and the SLEEP TIMER
is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency Control)
There are four possible settings for this option:
0 = Broadcast 1 = CATV (default)
2 = HRC 3 = IRC
If some channels were not found by Auto Tuning (Channel
Search), select the appropriate Band setting here, and add the
channels using the Channel Edit option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial Major
Start Channel number when the TV is turned ON. This feature is
useful for an in-house information channel, since the TV would
always select that channel when it is turned ON. If set to 255,
the last channel tuned before the TV was turned OFF will be the
channel tuned when the TV is turned ON again.
0 = Aux 127 = Map to Major CH 4
1 ~ 125 = Major Ch. # 253 = IP Start Channel
126 = Map to Major CH 3 255 = Last Channel
Note: For a digital Start Channel, always remember to set item
104 to the Minor Start Channel number.
Note: 126 and 127 are mapped only in SONIFI PPV Mode.
Note: The IP Start Channel shown above can only be set in the
FTG File Manager, which is used to congure TV CPUs for FTG
Mode. The same applies for the additional Major Channel number
range of 128 ~ 135 in Physical tuning and 128 ~ 999 in Virtual
tuning mode. This means that these values, if set, will only be
visible in the read-only Installer Menu when the TV is in FTG
Mode. The read-only display also will show additional information
about the channel, for example, the IP address and port number,
etc.
005 - CHAN LOCK (Channel Lock)
Channel Lock is ideal if the system must always be on the same
channel. Changing channels with the Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (default).
Generally, this feature is used in connection with item 004 STRT
CHANNEL where the Start Channel may, for example, be set to
3 or 4. If the Start Channel is 3, then the TV will remain locked on
channel 3.
NOTE: For items 007, 008, and 009
For legacy reasons, the scale used is 0 – 63. The PTC software
will translate this to the 0 – 100 scale used by the TV.
To translate a TV volume level to the Installer Menu value, use
the following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV will always select
that volume level when it is turned ON. The range of values is 0
to 63, 255. If set to 255, the last volume level before the TV was
turned OFF will be the current volume level when the TV is turned
ON again.
Detailed Descriptions of Installer Menu Items