Bosch Power Tools GCM12SD Saw User Manual


  Open as PDF
of 164
 

$
<@6A6<; F<B? /<1F .;1 5.;1@
=?<=2?9F A< :.82 0BAA6;4 2.@62?
.;1 @.32? .69B?2 A< 3<99<D .99 6;@A?B0A6<;@
612;A63621/29<D/F/B992A
l@F:/<9@:.F?2@B9A
6;@2?6<B@=2?@<;.96;7B?F@2264B?2
64B?2.;1$<@6A6<;@
l "2C2? =9.02 5.;1@ ;2.? 0BAA6;4 .?2. 22=
5.;1@ .;1 .?:@ <BA@612 A52 K"# "&L
G<;2
K"#"&L-#" – is defined as the entire table
plus the fixed portion of the base on the right and left
side of the table and portions of the fence within this
boundry. This zone is labeled with “No Hands”
symbols placed on the fixed base.
l 2.D.?2<3A52=.A5<3A52@.D/9.12!.82.
%,%(" D6A5A52@.DK#L/F0<;1B0A6;4
. @6:B9.A21 0BAA6;4 0F092 .;1 </@2?C2 A52
=?<720A21=.A5<3A52@.D/9.1222=5.;1@
<BA<3A52=.A5<3@.D/9.12
%,M%("– It is important to know where the blade
will intersect with the workpiece during cutting
operations. Always perform the simulated cutting
sequence with the power tool switched “OFF” to gain
an understanding of the projected path of the saw
blade. Mentally note where the path of the saw blade
will fall and set up your work to keep your hands and
arms out of the path of the spinning blade. Adjust
your clamps and fences so that the smooth lower
guard and cutting action is not interfered with during
cutting operation (see Figure 30).
l <91D<?8=620236?:9F.4.6;@AA./92.;132;02
A<=?2C2;A:<C2:2;A
l 22=5.;1@6;=<@6A6<;B;A69A?6442?5.@/22;
?
292.@21.;1/9.125.@0<:=92A29F@A<==21
l "2C2? =9.02 5.;1@ <; :205.;6@:
0<:=<;2;A@
l 22= 322A 36?:9F <; A52 39<<? .;1 :.6;A.6;
=?<=2?/.9.;02
l <99<D A52 :6A2? .?: D52; :6A2?6;4 923A <?
?645A &A.;1 @9645A9F A< A52 @612 <3 A52 @.D
/9.12
'52 9<D2? 4B.?1 :.F ;<A
.BA<:.A60.99F <=2; B;12? 02?A.6;
0BAA6;4 0<;16A6<;@ 3<? 2E.:=92 D52; A?F6;4 A<
0BA D<?8=6202@ A5.A .?2 ;2.? A52 :.E6:B:
0BAA6;4 52645A 0.=.06AF (;12? A52@2 0<;16A6<;@
<? 1B?6;4 A52 /9.12 A?.C29 :<A6<; <3 0BA A52
D<?8=6202 0.; @A<= A52 9<D2? 4B.?1 :<C2:2;A
/23<?2 A52 1<D;D.?1 :<A6<; <3 A52 .?: 0<B91
=?2<=2;A529<D2?4B.?1
If this occurs:
Workpiece must be securely clamped. This frees a
hand to raise the guard by the lip just
enough to clear the workpiece (see Figure 31).
Start the saw and begin your cut.
Once you have cleared the position where the lower
guard may bind, release the guard and it will continue
to operate automatically as you cut.
64B?2%.6@6;4 <D2?B.?1
*%""
!
*%""
!
Workpiece
Lower
Guard
Lip
Clamp
Preparing for Saw Operations
<1F.;1.;1$<@6A6<;
BM 2610007877 04-10:BM 2610007877 04-10.qxp 4/26/10 8:13 AM Page 28
 previous next