Filter
Top Products
K&)'&"&'%('#"&L
l (@2 @.32AF 2>B6=:2;A 9D.F@ D2.? @.32AF
4<4492@ Dust mask, safety shoes, hard hat or
hearing protection must be used for appropriate
c
onditions. Everyday eyeglasses only have
impact-resistant lenses, they are NOT safety
glasses.
'<<9(@2.;1.?2
l (@209.:=@<?<A52?=?.0A60.9D.FA<@20B?2
.;1 @B==<?A A52 D<?8=6202 A< . @A./92 =9.A
3<?: Holding the workpiece by hand or against
your body is unstable. It allows for workpiece to
shift, causes binding of the tool and loss of
control.
l < ;<A 3<?02 A<<9 (@2 A52 0<??20A A<<9 3<?
F<B?.==960.A6<; The correct tool will do the job
better and safer at the rate for which it is
designed. Do not use the tool for purpose not
intended - for example, do not use the miter saw
for slicing meats.
l <;<AB@2A<<963@D6A051<2@;<AAB?;6AK#"L
<?K#L Any tool that cannot be controlled with
the switch is dangerous.
l 6@0<;;20A A52 =9B4 3?<: A52 =<D2? @<B?02
/23<?2:.86;4.;F .17B@A:2;A@<?05.;46;4
.002@@<?62@ Such preventive safety measures
reduce the risk of starting the tool accidentally.
l 22=0BAA6;4A<<9@@5.?=.;1092.; Properly
maintained tools, with sharp cutting edges, are
less likely to bind and easier to control. When
mounting saw blades, be certain that the arrow
on the blade matches the direction of the arrow
marked on the tool and that the teeth are also
pointing in the same direction.
l ;@=20A 4B.?1@ /23<?2 B@6;4 . A<<9 22=
4B.?1@ 6; =9.02 5208 :<C6;4 =.?A@ 3<?
/6;16;4<?.;F<A52?0<;16A6<;A5.A:.F.3320A
A52;<?:.9<=2?.A6<;<?@.32AF32.AB?2@<3A52
A<<9 3 1.:.421 5.C2 A<<9 @2?C6021 /23<?2
B@6;4 A52 A<<9 Many accidents are caused by
poorly maintained tools.
l < ;<A .9A2? <? :6@B@2 A<<9 Any alteration or
modification is a misuse and may result in seri-
ous personal injury.
l '52 B@2 <3 .;F <A52? .002@@<?62@ ;<A
@=20636216;A56@:.;B.9:.F0?2.A2.5.G.?1
Accessories that may be suitable for one type of
tool may become hazardous when used on an
inappropriate tool.
&2?C602
l '
<<9 @2?C602 :B@A /2 =2?3<?:21 <;9F /F
>B.963621 ?2=.6?=2?@<;;29 Service or mainte-
nance performed by unqualified personnel may
result in misplacing internal wires and compo-
nents which could cause serious hazard.
l *52; @2?C606;4 . A<<9 B@2 <;9F 612;A60.9
?2=9.02:2;A =.?A@ <99<D 6;@A?B0A6<;@ 6;
A52 !.6;A2;.;02 .;1 B/?60.A6<; @20A6<; <3
A56@ :.;B.9 Use of unauthorized parts or
failure to follow maintenance instructions may
create a hazard.
&.32AF%B92@3<?!6A2?&.D@
l To reduce risk of injury, use saw blade rated
3800/min (RPM) or greater.
l (@2 09.:=@ A< @B==<?A D<?8=6202 D52;2C2?
=<@@6/923@B==<?A6;4A52D<?8=6202/F5.;1
F<B :B@A .9D.F@ 822= 5.;1 <BA@612 <3 K"<
.;1L .?2. .@ :.?821 D6A5 . @F:/<9 <; A52
/.@2<;<AB@2A56@@.DA<0BA=6202@A5.A.?2
A<<@:.99A</2@20B?29F09.:=21Your hand, if
placed inside the “No Hands” region, can easily
slip or be pulled into the blade.
l <;<A?2.056;/.08<3A52@.D/9.12/256;1
A52 32;02 D6A5 26A52? 5.;1 A< 5<91 1<D; <?
@B==<?AA52D<?8=6202?2:<C2D<<1@0?.=@<?
3<? .;F <A52? ?2.@<; The proximity of the
spinning saw blade to your hand may not be
obvious and you may be seriously injured.
l "2C2? 0?<@@ F<B? 5.;1 <C2? 6;A2;121 96;2 <3
0BAA6;4 Supporting the workpiece “cross hand-
ed,” i.e., holding the left side of the workpiece with
your right hand, is very dangerous.
l 9D.F@ 16@0<;;20A A52 =<D2? 0<?1 3?<: A52
=<D2?@<B?02/23<?2:.86;4.;F.17B@A:2;A@
<? .AA.056;4 .;F .002@@<?62@ You may
unintentionally start the saw, leading to serious
personal injury.
l !6A2?@.D@.?26;A2;121A<0BAD<<1<?D<<1
9682 =?<1B0A@ A52F 0.;;<A /2 B@21 D6A5
./?.@6C2 0BA<33 D5229@ 3<? 0BAA6;4 32??<B@
:.A2?6.9 @B05 .@ /.?@ ?<1@ @AB1@ 2A0
<D2C2?630BAA6;4:.A2?6.9@9682.9B:6;B:<?
<A52?;<;32??<B@:2A.9@B@2<;9F@.D/9.12@
@=206360.99F ?20<::2;121 3<? ;<;32??<B@
:2A.90BAA6;4Cutting ferrous materi-als causes
excessive sparking and will damage the lower
guard and overload the motor.
Safety
“
READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by
BULLET (
l) symbol listed BELOW, and other safety precautions, may result in serious
personal injury.
*%""
!
BM 2610007877 04-10:BM 2610007877 04-10.qxp 4/26/10 8:13 AM Page 3