Section 8: Specifications In-Sight
®
1700 Series Wafer Reader
88
8.1 General Specifications
Table 8-1: In-Sight 1701 Wafer Reader General Specifications
SPECIFICATION DESCRIPTION
Configurations
• Vertical Mount w/ factory-set 10 mm Working Distance (P/N 800-5797-1)
• Vertical Mount w/ factory-set 50 mm Working Distance (P/N 800-5798-1)
• Optional Horizontal Mirror Mount (800-5796-1)
Firmware
In-Sight version 2.40 and later
Supported Wafer Marks Standards
SEMI font SEMI M12, M13, M1.15
IBM font N/A
OCR
Triple font N/A
2D Data Matrix™ (ECC 200, 8 x 32) SEMI T7 and M1.15
Reading Capability
Barcode BC 412 and IBM 412 SEMI T1-95
Job/Program
8MB non-volatile flash memory; Unlimited storage via remote network device
Memory
Image/Processing
16MB SDRAM
1/3-inch CCD (5.80 x 4.92 mm, 6 mm diagonal)
1024 x 768 pixel display (307,200 sq. pixels, 4.65 x 4.65 µm)
Image Sensor
Electronic shutter speed: 64 µs to 33 ms; Up to 18 frames per second
Rapid reset, progressive scan (supports partial scan), full-frame integration
256 grey levels (8 bits/sec)
Acquisition
Gain controlled by software
Lighting/Optics
Field of View: 31 mm (W) x 23 mm (H)
Working Distance: adjustable, w/ factory-set options of 10 or 50 mm (Vertical)
Illumination Area: 31 mm (W) x 19 mm (H) (Nominal; depends on Light Mode)
Red LEDs, 626 nm wavelength, w/ Bright Field and Dark Field modes
Variable intensity controlled through software
I/O* Trigger
1 opto-isolated, acquisition trigger input
Remote software commands via Ethernet and RS232
None built-in
Discrete Inputs
8 inputs available using optional I/O Expansion Module (P/N 800-5758-1)
Unlimited inputs using optional Ethernet I/O Module (P/N CIO-ENET-IN4)
None built-in
Discrete Outputs
8 outputs available using optional I/O Expansion Module (P/N 800-5758-1)
Unlimited outputs using optional Ethernet I/O Module (P/N CIO-ENET-OUT4)
Status LEDs
1 Network Traffic, 1 Network Status, 1 Network Speed, 2 User-Configurable
Network
1 Ethernet port, 10/100 BaseT, TCP/IP protocol. Supports DHCP (factory default) or
static IP address. Manual reset switch disable DHCP and forces factory-assigned, static
IP address.
Serial
1 RS-232C port (1200 to 115,200 baud rates)
Communications
Protocols
In-Sight, Native Mode and Electroglas
Power
24 ± 10% VDC; 125mA (illumination off) to 200mA (illumination on)
Material
Aluminum housing, black anodized
Mounting
Four 6.5 mm deep M4 threaded mounting holes (two per side)
Dimensions
116.7 mm (4.60 in) x 69.9 mm (2.75 in) x 57.6 mm (2.27 in)
Horizontal configuration length: 141.3 mm (5.55 in)
Mechanical
Weight
416.7 g (14.7 oz)
Temperature
10 to 45°C (Operating), -10 to 65°C (Storage)
Environmental
Humidity
10 to 90%, non-condensing (Operating and Storage)
Certifications
CE, CUL
* See Section 8.2: I/O Specifications for more information.
