Filter
Top Products
1.6
FCC Regulations for Telephone Line Interconnection
1. This equipment complies with Part 68 of the FCC rules. On the outside surface of this equipment is a label that contains, among
other information, the FCC registration number and ringer equivalence number (REN). If requested, this information must be provided
to the telephone company.
2. A suitable jack (USOC connecting arrangement) for this equipment is shown. If applicable, the facility interface codes (FIC) and
service order codes (SOC) are described.
3. The ringer equivalence number (REN) is used to determine the quality of devices which may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all
areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line,
as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
4. If this equipment causes harm to the telephone network, the telephone company will notify you in advance. But if advance notice
isnt practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
5. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of
the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications
in order to maintain uninterrupted service.
6. If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc. at the
address shown below for details of how to have repairs made. If the trouble is causing harm to the telephone network, the telephone
company may request you remove the equipment from the network until the problem is resolved.
7. No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void
registration and warranty.
8. This equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is
subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for
information.)
9. If so required, this equipment is hearing aid compatible.
Manufacturer: Multi-Tech Systems, Inc.
Model Number: #MMV16XXC/56/56/V
#MMV32XXC/56/56/V
FCC Registration Number: AU7USA-18883-DE-N (DSU)
AU7USA-20328-MD-E
Ringer Equivalence: 0.3B (Command modem)
Modular Jack (USOC) RJ11C or RJ11W (single line)
Service Center in U.S.A. Multi-Tech Systems Inc.
2205 Woodale Drive
Mounds View, MN 55112 USA
(612) 785-3500 or (800) 328-9717
U.S. Fax (612) 785-9874
1.7
DOC Terminal Equipment
Notice: The Canadian Department of Communications label identifies certificated equipment. This certification means
that the equipment meets certain telecommunications network protective, operational and safety requirements. The
department does not guarantee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. In
some cases, the companys inside wiring associated with a single line individual service may be extended by means of
a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian facility designated by the Supplier. Any
repairs or alterations made by the user to this equipment; or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should insure for their own protection that the electrical ground connections of the power utility, telephone lines
and internal metallic water pipe system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a
telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any
combinations of devices subject only to the requirement that the total of the Load Numbers of all the devices does not
exceed 100. The load number for the Command Modem is 7.